Failure rate of BSR202N
Hello to everyone. I want to find the Failure rate of a component of BSR202N? Can someone send me the reliability data of this?
View ArticleClik here to view.
Can anyone please tell me how to solve this problem?
Attachment 2813 please tell me what do i have to do in this step in IFX config wizard? ????? Capture.PNG‎ (23.1 KB)
View ArticleClik here to view.
[XMC4800] USIC as SPI - MSLS Problem
Hello, I would like to use some GPIOs as additional Slave Select signals. But I do get a timing problem with the gpio slave select signal. it is way faster then the hardware slave select signal. My...
View ArticleUSIC as UART, XMC1300
Hi IÂ’m doing some code using the XMC1300 boot kit and XMClib. IÂ’m using the USIC channel as UART. The transmit function is working but not the receive function. Can someone help me?? In this example I...
View ArticleMIgrating DAVE example project from XMC1302-T38 to XMC1302-Q40
Hi, I am looking to migrate the BLDC_SCALAR_HALL_XMC13 example from XMC1302-T038 to XMC1302-Q40. How can the migration be done in the latest version of DAVE 4.3.2?
View ArticleXMC4800/XMC/4300 on EtherCAT
Hi , Could XMC4800/XMC4300 fully simulated ET1100 ? if yes , do anyone know 3rd party support this solution? EX : XMC4800/XMC4300 commutation protocol by SPI is fully the same as ET1100. We just let...
View ArticleImplement FMCW on Sense2go board
MCU:XMC4200 Hello I would like to know if the hardware of Sense2go board is qualified to implement FMCW, especially the VCO part. Actually, recently I've been coding the FM modulation by adjusting the...
View Articlehttps://circlehealthclub.com/nitric-muscle-fuel/
https://circlehealthclub.com/nitric-muscle-fuel/ Aging is always accompanied with lot many side effects. One such side effect in men is decrease of testosterone levels in men. This decrease also...
View ArticleReference code for I2C and ADC on Aurix TC297 micro controller
Hello, We are working on Infineon's TriCore Aurix TC297 micro controller. For this we have purchased KIT_AURIX_TC297_TFT kit from Infineon Technologies. For programming the kit we are using HighTech...
View ArticleCoolMOS in a medium/high power switching application
Seems OK to me, I just used the LIB file "as is", created "default rectangular" parts and wired up a trivial test circuit, I am getting currents of the order of Amps so I would reckon that to be...
View ArticlePWM with CCU8
Hello, Quote: You Need to reload both the multichannel gating in the Posif and the Duty Cycle in the CCU8. In the Reference manual of the XMC1302 on Page 921 is described, that the timer Values (Duty...
View ArticleMosfet circuit Hints
I am using an Infineon type to-220 mosfet in my circuit. To "turn it on" I need to ground one of the pins.....which is only low current hence I'd like to make use of the uno. This pin when not grounded...
View ArticleClik here to view.
Save 4.3.2 Static memory analyzer does not work for me
Hello everybody, I am using Hegagon XMC4500 dev board with Dave 4.3.2. On Dave Release notes it is indicated that a new Window - View could show grafically memory usage from elf / map files. But this...
View ArticleFAQ for XMC4800 EtherCAT
Hi, @ FHK: do you know already more about your question? I also ask myself if it is possible to only use one EtherCAT port. Or does an EtherCAT Maser usually need two ports? Best regards
View ArticleXMC 4500 Ethernet failure
Hi shenj, Sorry for the delayed answer being busy with many topics. I was able to reproduce your issue. In my case the solution has been to increase the stack size of the Ethernet task. In your main...
View ArticleSlow progress...
Anyone else experiencing DAVE4.3.2 hanging for around a minute on opening a workspace, with the 'Progress Information Operation in progress..' dialogue showing ? Have a solution to speed up? Seems to...
View Articleoffset supply voltage transient of a MOSFET
It is the maximum rate at which the voltage at the VS pin can change is 50 V/ns. This high degree of tolerance makes the IC robust, and ensures excellent device performance in demanding applications...
View ArticleXMC1302 UART Transmit FIFO Configuration
Hi kepl, so why does the DAVE APP permits FIFO size of multiples of two is because the specification defines that :) "The size of a FIFO data buffer can only be programmed as a power of 2, starting...
View ArticleTC1796 writing OTP area of engine computer
Im looking for someone who can help me read and write a OTP area on a TC1796, This is in relations to a Audi/VW Engine Computer Memory configuration Sector Address Size Type User0 WP User1 WP 00...
View ArticleBLDC FOC control with Encoder Feedback
hi can anyone support me with an example of BLDC control the Control technique used is FOC control , we have a Encoder attached to the motor , if any APP available for BLDC FOC control with Encoder...
View Article