Choosing pins for external interupt
Hello Paul, the Port I/O Functions table is the correct document to consult. A pin which is capable of being used as an interrupt source needs to be connected to the ERU. Have a look at the "Inputs"...
View ArticleClik here to view.
ATTENTION: Update your SEGGER JLink version to latest version (V6.20a as of...
I have learned older SEGGER versions have problems to erase flash (timeouts) before downloading the binary. This is especially true if your binary is bigger >256K. You will see strange...
View ArticleSense2Go Development Kit Exporting Data
Hi jjn123, may I please know if your kit is really the old (outdated) Sense2Go platform or successor platforms like Sense2Go2 or Sense2GoL? For latter ones we have software updates that are able to...
View ArticleClamping extension to pins
Hello, For one of the extensions to an existing design, I thought of adding clamps to the following question using general purpose diodes. Does this look right? I wasnt sure if one needs a current...
View ArticleLooking for a tool to get website ip address!
Hello guys, As the title says, I need a seo tool which can be used to get website ip address. Do you know this kind of tool? If yes, which one do you use? I found a seo tool http://zzday.info/ This one...
View ArticlePMSM_SCALAR_CTRL App
hi, I am checking Apps in Dave help and looking for PMSM_SCALAR_CTRL. this app was mention in Dave help but I am not able to find the app in Dave 4.3.2. is App still available ? Thank you. Best...
View ArticlePspice Simulation with IR 2113
Hello, I am trying to setup a half bridge simulation with IR 2113 and IPx60R125 devices. I have a boot strap circuit and have also charged the capacitor by giving pulse to low side switch first. The...
View ArticleHow to give the master a random and a short address to my slave device?(DALI...
I have not met this situation before
View ArticleI2C Xmc4700 Relax Kit
Hello everyone, I'm trying to use the example on i2c_master.h from line 805 to 827 to use I2C bus in the Xmc4700 Relax kit, I chose pin P0.13 and P3.15 on the DAVE CE (Manual Pins Allocator) and in...
View ArticleSense2GoL Implementing FMCW
Hi Kasper, unfortunately with the Sense2GoL platform it is not possible to operate FMCW modulation for two reasons 1. Microcontroller used does not have a DAC to drive the ramp 2. The port for tuning...
View ArticleClik here to view.
IR2110 high side
Hello, I followed that tips and now my H bridge is working well, just want to say thank you very much and ask one more question: when using the IR2110 with high frequencies of 500 kHz until 1 MHz, does...
View ArticleLWIP eternetif.c driver latest status
Nice. Where can I download it? Why DAVE does not find new updates? rum
View ArticleThe DAVE4.3.2 doesn't support DAP miniwiggler，only support Jlink？
:eek:?I can't find the selection of "universal debug access debug" like DAVE3.1.10.And I can't debug or download program using DAP miniwiggler under DAVE4.3.2. Thank you.
View ArticleDAVE4 + I2C = Problem. (XMC2Go)
Hi, It should work also in DAVE4. Did you check with a logic analyzer what is going on in the line? Which kind of sensor are you trying to interface? Regards, Jesus
View ArticleNo source avaliable for "0x8004614"
Hello everyone, i'm working, for the first time, with a microcontroller XMC4500 and when i compile DEBUG at the end i have this message : No source available for "0x8004614()". What does it means?...
View ArticleXMClib POSIF as Quadrature encoder example.
I use an incremental encoder, and try to use the index signal to reset the position count to prevent the position error accumulation problem. The index signal is connected to the CCU41 event0. I...
View ArticleEtherCAT SSC Tool - uint16 arrays and uint32 values
Hi all, I am working on EtherCAT with the SSC Tool. I have big trouble to send UINT32 values and UINT arrays. Does anyone have an example .xls file which can be imported into SSC Tool (called...
View ArticleSMPS by using ICE2HS01G
What is the link to your design in Infineon Designer? Please describe your problem.
View ArticleCPU_TC.048 TC1796 Need for NOP before RET?
http://www.tasking.com/support/trico...guide_v3.0.pdf page 807 Tasking compiler/assembler manual says, "The assembler gives a warning when there is no or just one instruction (not a NOP instruction)...
View ArticleCCU4 capture register contains no data with XMC1300 internal temperature over...
We have an LED lighting application using DALI, based on XMC1300. The lamp must operate continuously at over 85°C. We discovered in testing that the DALI interface fails to receive data when the MCU...
View Article