Implementing FMCW on XMC4400 microcontroller
can I get FMCW SW for the BGT24RFB2412 now?
View ArticleXMC1100 - can not add a second uart
Hi, i use XMC1100-T038X0064. the first uart works perfect, Standard pins used: P1.2 and P1.3 now i would like to setup a second UART on Pins P1.0 and P1.1. Up to this moment they are free, not used by...
View ArticleTag Connect
Is there any interest in having a Tag Connect solution for use with XMC Link and a target board? Presently I'm putting a 0.05" 10 pin female header on our engineering boards for programming. My problem...
View ArticleClik here to view.
Phase Shift PWM with XMC4500 relax kit
Hi folks! Using the XMC library (toolbox matlab for automatic code generation), is it possible have a phase shift PWM at 100 KHz ? More exactly, I need 4 synchronized PWM signals for the control of a...
View ArticleXMC4500 Clock frequency
Hi Szymon, check "CLOCK_XMC4" APP. Under "Clock Selection Settings" you should find exactly what you need ;) Best regards, Deni
View ArticleDMA Transfer complete question
When is the DMA transfer complete Interrupt set? I am using the DMA to Transfer data from Memory to a USICin SPI mode. In the DMA Interrupt set to "Transfer complete" I remove the slave select signal....
View ArticleClik here to view.
TC297 Application Kit Schematics
i have found some document in MyICP portal but that ducument did not support TC297 mcu as is that document it is mention starter kit manula Tricore board TC2x7 but in document i have found Attachment...
View ArticleRegarding Temperature sensor pin for TC233 Aurix Microcontroller
Hi, I see in the datasheet that there is section included for temperature sensor, I need to know whether TQFP-100-23 , which pin would support/ give temperature sensor output. I do have the datasheet...
View ArticleRecommendation document for AURIX TC233 100pin package microcontroller for...
Hi, Is there any guidelines or recommendations document available for SAK-TC233LP-32F200F . If possible can i get a reference schematics for the part no. shown.
View ArticleFAQ for XMC4800 EtherCAT
Hello all, we want to build our own EtherCAT slave based on an XMC4800. So far something is runing on the eval board. Now, we have to build our own Hardware. I thought let's use the BCM5241 PHY like on...
View ArticleIRMCK311 Custom Programming Methods
Dear Support, IRMCK311 Custom Programming Methods by JTAG, Can you give me some detailed information. For example: Hardware design, Operation Flow, Precautions etc. Thanks The following procedure,I try...
View ArticleXmc debug
Hello at all, I want to use the XMC Debug Command to Debug my Code. Examle: XMC_DEBUG("DAVE APPs initialization failed\n"); Where is this issue displayed? Reguards, Patrick
View ArticleTLE4997 linear hall sensor source code
Hey guys. I'm using TLE4997 in one of my projects and I only get voltages from 2-3V. I want to get full 0-5V scale and it looks like I will need to program it according to the programming protocol. Is...
View ArticlePorting Micro-Python onto TC1784/82 micro controller board
Hi, Can any one help me in porting micro-python onto custom TC1784/82 micro controller board.? I am new to Infioneon. Currently I am working on an automotive project include C-Programming. Now, I...
View ArticleClik here to view.
Infineon TLE9879 Eval Kit Bridge short problem
Dear all, Any one has experienced the TLE9879 Eval kit Bridge drive short problem? I am not able to switch on the BRIDGE DRIVE(BRDV) because it shoes Bridge drive is short and Low voltage at VCP....
View ArticleClik here to view.
sharing XMC input pin for ADC and Comparator Input
Hello, I am using XMC1300, TSSOP-16. I wanted to know if I can use the pins for Comparator input as well as for ADC input at same time to save pins. In XMC pinout tool, it shows as RED. Attachment 3244...
View ArticleClik here to view.
ETH_LWIP slimdown
Hi, I'm trying to reduce the RAM consumption of ETH_LWIP. Could anyone suggest some reasonable reductions, from the settings below ? I inherited the settings from the Infineon DAVE example project for...
View ArticleDAVE configure SPI in a way that keeps the CS-line low within a frame.
Hi Lukas, you should also check SPI_CONFIG APP especially "Keep the Slave Select signal active after a frame has been transmitted" under "General" tab. This will call "XMC_SPI_CH_EnableFEM(channel)"...
View ArticleIs LQFP-144 XMC4500 and LQFP XMC4700 Pins definition same
hi, I have one XMC4700 Relax kit board, we will design one board based on XMC4500. Can anyone tell us if using the same package(LQFP-144), XMC4500 and XMC4700 are pin to pin compatible? So we can check...
View Article