Error occured while connecting to the solver process
Thank you Jesus. But it doesn't work. Any other advice?
View ArticleClik here to view.
Error occured while connecting to the solver process...PLS HELP!
Hello Alibabara. I got the same problem. I understand what you feel. We better make a new forum other than this, because this forum is dead for a long time. Even Lord Jesus's answer is not helping...
View Article일산op♐일산건마OP쓰7닷&...
일산op♐일산건마OP쓰7닷컴♐일산키스방힐링사이트 일산오피 일산후기え일산밤문화 일산안마 ん일산마사지♥일산유흥할인정보 일산휴게텔 오피쓰
View ArticleGet up-to-date on XMC and DAVE!
Never miss out on the latest, get up-to-date on XMC and DAVE. From link below, click on option inside "Forum Tools" to subscribe to respective sub-forum and receive email updates on a regular basis...
View ArticleTorque Control on FOC Sensorless Demo app (not working)
Finally, we got the motor running under a torque control scheme. What we used for the succesfull run was the demo within the DAVE repo, but it was required to change the Iq set at the control settings,...
View ArticleXMC4500 Internal Back up clock
Finally I myself found it in the header file of XMC4500 "system_XMC4500.c" that the value is 24 Mhz.
View ArticleFOC Sensorless questions and thoughts
I have spent the last days evaluating and reviewing the XMC FOC sensorless libraries for an ebike solution proof-of-concept. Here I expose certain thoughts and questions that came up... - I have...
View ArticleDemodulate BMC-Signal using CCU4_Slice_Config app
Hello, I would like to demodulate a Biphase Mark encoded signal with an XMC1100. The signal has a constant frequency of 2kHz. The binary value 1 is displayed as a transision within a period. The binary...
View ArticleC167CS-LM could not able to distinguish between different reset.
Hello Infineon, We have two C167CS-LM populated on two different hardware which are identical in terms of schematic and components. One of the controller detect all the type of reset appropriately and...
View ArticleXC2797 Software Reset does not restart software
Hello, I've got the problem while working on an remote controlled load with an XC2797 as it's controller. We would like to have the option to trigger a reset over an dedicated uart command. The command...
View ArticleClik here to view.
Temperature Sensor of BGT24MTR11 -- wrong transfer function equation
Quote: Originally Posted by dagern Hi Jhon, we have double-checked the transfer function and it seems to be outdated. Please calibrate the sensor according to the attached pdf to get the accuracy...
View ArticleXMC 4500 SPI trigger transfer extern
I have running SPI-Master with DMA for TX und RX, transfer is started via function XMC_USIC_CH_TriggerServiceRequest(XMC_SPI1_CH0, 0); Is it possible to start the SPI with an external PIN ? I want to...
View ArticleFOC Sensorless questions and thoughts [Case:3760197]
I have spent the last days evaluating and reviewing the XMC FOC sensorless libraries for an ebike solution proof-of-concept. Here I expose certain thoughts and questions that came up... - I have...
View ArticleMicrocontroler - Multiple I/O
Hi everyone, looking for some advice on a programable chip that I can use to control multiple source signals to monitor a value, then turn on or turn off depending on that signal... E.g. A temperate...
View ArticleImplementing RDM over DMX-512
I'm newbie in ARM microcontrollers. But I successfully implement DMX-512 for driving leds (9-ch BCCU, UART etc) and it works fine. But I have pack of troubles with implementing RDM (remote device...
View ArticleClik here to view.
IRF200P222 and 1EDN7512
Hello, I will control a brushed DC motor using low side switching. [Picture attached] How can I match the gate driver 1EDN7512 with this MOSFET (IRF200P222)? It has two inputs (IN+ and IN-) and one...
View ArticleClik here to view.
DAVE CE "Break point Installation Failed: Unmatched Quote"
Hello, I am having trouble with breakpoints setting. When i double click on line number warning appears "Break point Installation Failed: Unmatched Quote". Also when i Suspend/Terminate Debug "No...
View Articleproblem with update of version 4.4.2
Hi, I got problems with athe update of SW, which Dave has itself found: i Got a message: An error occurred while collecting items to be installed session context was:(profile=profile,...
View ArticleClik here to view.
XMC4500 (100 Pin) single phase shift dual active bridge
Hallo , to controle a dual active bridge, i need 8 PWM signals , as you can see in the picture below,every two MOSFET blong to a group from A to D. HSX (high side) and LSX (low side) need a dead time...
View ArticleXMC4700. UART receive timeout interrupt - is it possible to?
Sorry for bumping this old thread. I wanted to implement the proposed solution to connect UART to ERU to CCU4; but to me this seems not possible. All service request lines SR[0-5] of the USIC connect...
View Article