XMC4500. Transmit Flash->DMA->USB - impossible?
When I studied the low-level driver (xmc_usbd.c) from "XMClib v2.1.6 - XMC Peripheral Driver Library", I found certain bug: The XMC_USBD_EP_t :: outInUse flag is reset (set to "0") in many places...
View ArticleHow send data by udp between PC and XMC4800 Relax EtherCAT Kit
It would be a great help for me.
View ArticleTC3xx CAN Examples and Libraries Availability
Good Morning, I'm fairly new to the Aurix boards environment. I've been tasked to create some small project that enables CAN communication between the board and an external device. I've managed to find...
View ArticleWhat is the difference between CPU watchdog and safety watchdog?
Hello, Similar to the CPU Watchdog example as in https://www.infineon.com/dgdl/Infine...6f9f46e55319ab Is it possible to provide an example of using the safety watchdog timer? It will be really useful....
View ArticleSMU Configuration Steps
Hello, I am experimenting with the watchdog timers. I found this example very useful for the CPU watchdog: https://www.infineon.com/dgdl/Infine...6f9f46e55319ab Is it possible to provide a similar...
View ArticleClik here to view.
Cannot simulate the .lib file of TLE4253 in Simetrix
Need an un-encrypted (working) spice model of TLE4253 to simulate in Simetrix. While simulating in simetrix , I received the below error. " Errors found during the run. Simulation aborted *** ERROR ***...
View ArticleSOTA Feathure Tc38x
Hi I am writing an application for SOTA concept for TC38x Aurix platform. I have read the chapter 1.5 AURIX2 usermanual (Software over the Air (SOTA)) And also referred the document...
View ArticleIGBT module f4-75r06w1e3 for a three phase inverter application
hi, I would like to know wether this issue got resovled or not. I am also facing the same issue. I am using tis for single phase inverter with HCPL316J and the IGBT module keeps going bad.
View ArticleIRFP7530PBF Current Issue
I have a DC load circuit using IRFP7530PBF. It is simple design as follow: - The gate of the MOSFET have a 10K resistor to ground and a DAC (Digital to Analog Converter) generating from 0 to 10 Volts....
View ArticlePWM toggling between active high or low, to high z (tri-state).
Does XMC 1xxx and/or XMC 4xxx series support toggling pwm output from high (or low) to tri state. As in instead of D = high and D-1 = low to for instance D=high/3.3V and D-1=High-Z/floating. Or would...
View ArticleParity/CRC error on load
Trying to use the TC234 ADAS ASCLIN module for serial, and I'm having this problem: IfxAsclin_setCtsInput(cts->module, (IfxAsclin_CtsInputSelect)cts->select); 0x8001A652 19 EF C8 DF LD.W...
View ArticleHow to setup XC2365 microcontroller in DAVE4
Hello: I need to use XC2365 to build project in DAVE4,but how to do?
View ArticleClik here to view.
Miniwiggler v3 read TC1736
Hello, can anyone share few ideas about Mini Wiggler V3 and TriCore TC1736? I'm trying to read it via JTAG, using following pads - TDI / TDO / TCK / TMS / VREF / GND / TRST, also voltage supply on...
View ArticleIRPS54012: LDO (Page 4 ~ Channel 5 ) VOUT readout gives wrong results
Hi Infineon, I'm trying to readout 3x IRPS54012 devices located on our custom PCB. For the Switchers all goes well ( page 0 -> page 3 ) Except for the LDO readouts I'm getting different results....
View ArticleClik here to view.
XMC1202 with ULINK2?
Thanks for reply! I follow all your step.. but nothing I'm not able to change this BMI. The file attached is the J-link commander sequence, it seems that it see the XMC but not able to connect with it,...
View ArticleClik here to view.
IR2136 application circuit
Hello everyone, I use the gate driver ic IR2136, when I measure between VB1 and VS1 I haven't 15V, I have to put the source pin of the mosfet transistor at the GND to have a potential difference of 15V...
View ArticleClik here to view.
problem : start a motor with Mce Designer
Quote: Originally Posted by Casey Hi Marcuccio1995, What is your DC Bus Over-value set as? Please provide me a screenshot of the parameters in MCEWizard (from the advanced page like the example) and I...
View ArticleClik here to view.
AURIX Development Studio Version: 1.1.6
Hello all, Greeting! I would like to ask for the IDE question about the variables watch on debug. I can press right button to select "Number Format", but HEX format is not available! ????? watch...
View ArticleFTP server example
Hi ,all: Is there any example about the usage of FTP server on XMC47/48 series? I want to transfer file from PC to XMC processer with FTP protocol, but could find no such example. The FTP APP compiled...
View Article