TC27x Application Notes
Hi, I can't give you a link, but I can tell you how to get there. First logon to MyInfineon. Next scroll down to the "Library Root" section. Then expand the "AURIX general" category and in here expand...
View Articlexmc4500_relaxkit_lwip_httpserver_netconn compile / link error
It is not possible to compile this example with DAVE Version: 4.2.2. Some directories are missing in the includes folder. If i include all the needed folders the linker is not able to generat the elf...
View ArticleADC - data reudciton - more than 4 samples?
Is it possible in data reduction mode to have more than 4 samples? Max, is 4 result values. Could one somehow use the fifo to trigger a interrupt when it is full and then read out all the data, this...
View Articleerror in document
Hi zbyno, Thanks for highlighting this. I have forwarded this to the relevant to fix the link! Regards, Daryl :)
View ArticlePWMSP001 BUG on XMC1100 with DAVE3
Hi, I do not have any issue on my setup with the above configuration. Can you create a new project with another APP to see if you still have an error generating the code? Also, can you share your...
View ArticleClik here to view.
Visit our booth at Light + Building 2016
Visit Infineon at Light + Building 2016, Hall 4.0, Booth F25 March 13th and March 18th, Frankfurt Attachment 2146 With innovative approaches for power conversion and intelligent control, Infineon is...
View ArticleXMC4500 remove protection
Hi Travis. Thank you for your help. I stored the attached file in a previous thread. After flash protection, 1. I closed memtool software and started the memtool again. 2. Plug out and plug in...
View ArticleETH_LWIP error in combination with the XMC4800
Hi Tobi, There is a solution to this. See this thread: http://www.infineonforums.com/thread...ate-Code-error Regards, Niclas
View ArticleGet_Time SYSTM001
can anyone help me to use this function Get_Time in app SYSTM001, i want to make project with HC-SR04 ultrasonic ranging module with DAVE 3 and XMC 4500 Relax Lite Kit, but i can't get time in ms to...
View ArticleHWSEL vs IOCR
hi, After I read user manual, I have some conclusion. 1. If HWSEL enable, IOCR = donÂ’t care. All of (in/out , pu/pd, open drain/pushpull) decided by HWSEL. SW canÂ’t control any block. ( EX: hwsel...
View ArticleStack depth analysis tool
Hi, You could use a empirical way: fill the stack with a known pattern, e.g. 0x5a 0x5a... , run the application and after some time check how many of the pattern has been overwritten. Another way is...
View ArticleBLDC MOTOR CONTROL USING XMC1400 Boot Kit
Hi, My name is chethan kumar recently i brought XMC1400 Boot Kit for bldc motor control application using PMSM_FOC app. This app only available for XMC1300 series, so did below mentioned procedure 1. i...
View ArticleABM Header
Hello, I got a question about the configurations for HWCON and SWCON. SWCON resets after a PORST as menitoned in the manual 11-69 and copies the content from HWCON. But when a system reset is made the...
View ArticleXMC1100 external interrupt timing problems
Thanks again for your help. I can use any pin I want for the external input signal, so I have tried to start the timer directly by the external start function (with P0.0) I think now it is a bit...
View ArticleClik here to view.
XMC 2Go - I2C - RGB Sensor
Hello ladies and gentlemen, I am a new member of the Infineon Forum and I hope that you guys are able to support me with your knowledge. I have been looking for several days to find some supporting...
View ArticleProblems with XMC1100 on new board
Hi, after successful development of several applications using the XMC1100 for Arduino board I am in the process of transfering hardware to a customized board. Because the software has been developed...
View ArticleClik here to view.
USIC/UART - PuTTY won't show Tx data; Tx pin is working
Hi all, In short, I am trying to send data to my PC over UART and PuTTY won't show anything in its terminal window (same goes for Docklight, although I used it very briefly). I have tried watching the...
View ArticleSettng BMI with DAVE
Hi, I am still trying to get XMC1100 running on a customized board. I am now understanding from various articles that there is an app for DAVE that enables to set BMI from DAVE. How can I get this app...
View ArticleCMSIS_RTOS_RTX problem with timers
Hi, I can't get the timer in CMSIS_RTOS_RTX to run. Thread stack and callback size for the timers in RTX are big enough. Code: void timer1callback(void const *arguments) {...
View ArticleXMC1100 40Pin QFN - SDW1 issue
Just for future reference this was all caused be cause if the length of the SWD wires. It seems that the Debuggers are very sensitive to this. So if you are getting intermittent debugging fails etc...
View Article