Optiga trust b sle95250
i am using optiga trsut B sle95250 fro electronic authentication. i have to write into the non volatile memory of the device according to the data sheet after successful writing of data . the NVM_ACT...
View ArticleTLE9879 FOC single shunt current sensing : How to know the real (physical)...
Hello, Thank you for your feedback. The formula allow as to deduce the value of the DC current. My question concerns the values of the two phase current in amp (EmoSvm.PhasCurr.A &...
View ArticleClik here to view.
MCEDesigner v2.3 crashes!!! EVAL-M3-IM564 MCEWizard config file!!!
Quote: Originally Posted by jerry_yang hi Casey, The discussion suggested that the new version might have some bugs, although I don't believe it. But the last version I'm using has some problems...
View ArticleTLE9879 FOC single shunt current sensing : How to know the real (physical)...
Hello, Thank you for your feedback. The formula allow as to deduce the value of the DC current. My question concerns the values of the two phase current in amp (EmoSvm.PhasCurr.A &...
View ArticleClik here to view.
MCEDesigner v2.3 crashes!!! EVAL-M3-IM564 MCEWizard config file!!!
Quote: Originally Posted by jerry_yang hi Casey, The discussion suggested that the new version might have some bugs, although I don't believe it. But the last version I'm using has some problems...
View ArticleIRFB3607 Turn on Delay
The Gate resistors are much to high, try a few Ohms and remove Diode + 2. resistor. You have to get 56µC in and out of the gate fast.
View ArticleSmart MOSFET BTS50055-1TMA will it support 62A
The ISO rating blindly assumes half a Volt drop over the switch, it gives 35W dissipation which at 33K/W equals 1155 deg. C above ambient. It probably is a left-over from the time these smart switches...
View ArticleBts6143d
Yes, the Pins has a pull-up to the supply and must be pulled low to switch on. A little inconvenient, it needs a transistor level shifter or an ULN2003 if there are more channels, a Micro pin won't do.
View ArticleIRS2007/2008 -- drive with DC control input?
High side Iq is 75µA max, or 270mC per hour. so a cap of 270000µF will droop one Volt. Good luck recharging that... Use a 1W DC-DC, they are just 5x10mm and solve your problem for good.
View ArticleTrouble Reading A11 Register
Hello I am having trouble reading the A11 Register. I tried: Code: __mfcr(CPU_A11) (&CPU0_A11)->B.ADDR *((unsigned int *)&CPU0_A11) //Also Tried with inline assembly int *res; __asm__...
View ArticleRoot Causes for SMU3[6]
Hello, What are the Root causes of SMU3[6] alarm in Aurix TC265D? The clock configurations are proper according to the Errata sheet (5 MHz is selected as target monitoring frequency). There are no...
View ArticleClik here to view.
User Mode UART and Register Write (0x06) command
hi, Is your calibration algorithm consistent with the description in the reference manual in the user UART interface? Here are the frames I captured while debugging the communication interface....
View ArticleClik here to view.
Build problem on DAVE CE Project in EAVE4
Attachment 4895This is the code That I added ????? 无标题.png (65.1 KB)
View ArticleClik here to view.
Hall delay angle
In the BC_HALL demo code, what is the function of it and how to set this parameter? Attachment 4896 ????? æè·.JPG (14.2 KB)
View ArticleIRPS5401 won't start / initial bring-up
thankyou roofing companies newcastle , roofers chula vista , roof repair escondido
View ArticleDriving Mosfet using PWM from arduino so as to achieve Linear region of...
thankyou music producer London , online healing courses
View ArticleNeed ClassD amplifier for 60 Hz transformer switching
thankyou accounting services Kent , seo company uk
View Article