Hall delay angle
Hi! This option is used in case you might need to compensate misalignments between the motor phases and the Hall sensors. The software takes into account this misalignments to generate a better synched...
View ArticleReceiving CAN Message from the wrong CAN-ID sometimes
Hello, I am using XMC4500 and have a problem, which occurs sometimes. In general my CAN-Communication works fine. Sometimes the received data and ID are mixed up with another message. For Example:...
View Articlequestion to NVM module
Hi, i am implementing the code for erasing and write operation on flash in tc3xx module. 1)before write operation any sector into particular page we need to erase the that sector first. 2)it is...
View Articlesimple interrupt question
Thanks, I will give it a try. Just to be clear, each core's table would only contain entries that that core would respond to? In other words, all 3 tables would be different?
View ArticleSOTA Feathure Tc38x
Now, sample code is available in myicp.infineon.com. Please refer below path. - Microcontrollers / AURIX customer documentation --> AURIX TC3xx --> 10 AURIX TC3xx HSM
View ArticleIf TESTMODE pin/ball is opened by any accident, the device will go into...
The default status of TESTMODE pin is pull-up. (It can be checked in data sheet) So, When TESTMODE pin is opened, generally we can say that there is no problem. But, this is really important pin for...
View ArticleStart bldc motor in different voltage imm101t
Hi Casey, I have already set DC bus under and over voltage. When switching from 220VAC to 150VAC, I always have to modify some params to make the motor start, which is inconvenient when it comes to fan...
View ArticleClik here to view.
Is there any way user can run HSM Core from TriCore for Aurix 2G?
Hello Support, Please confirm if foreground secure boot means SSWWAIT=1 and background secure boot means SSWWAIT=0 as shown below: Attachment 4905 Best Regards ????? HSM_SSWWAIT.png (128.8 KB)
View ArticleTC234LP32F200NACKXUMA1 Security Features
XC8xx and XC2xx are not supported any HW feature for security In case of 8-bit and 16-bit MCUs, there is not HW feature for security. From TC17xx, Infineon 32-bit MCU can support HW feature for...
View ArticleIMC101T Low Speed Performance
Hi, Im trying to develop a motor controller that can drive a particular BLDC motor between 0 and 300RPM using an IMC101T. Im getting good results at the higher speeds, but Im having real troubles at...
View Articlememtool programming - change COM setting programatically
hi all, im making an automatically programming procedure, that so far works well with the memtool 4.3. i did an .mtb file and via batch script i open the memtool with this mtb file and it programs my...
View ArticleWireless Charging with SLA Battery charging support
Checking if Infineon wireless charging supports SLA battery charging? (Sealed lead acid = SLA)
View ArticleLong-term Investments for future years
Money prices are relatively safe. There is a mutual fund where a group of investors invest their money with each other to buy stocks and options, bonds, or additional investments. I need to know more...
View Articlesimple interrupt question
what is a good strategy to keep who does what straight? It looks like it would be possible to have 2 cores assigned to the same uart, for example. I can imagine a single file where I have all of the...
View ArticleClik here to view.
Foreground Secure Boot Flag HSM2HTF.0 is set by HSM BOS or HSM User Code
Hello Support, With SSWWAIT=1, there is Foreground Secure Boot feature enabled in HSM. Looks like Host SSW Software will check for HSM2HTF.0 as 1 before jumping from Host SSW to Host User Code. During...
View ArticleIf TESTMODE pin/ball is opened by any accident, the device will go into...
No, device will not go in testmode. The internal pull-up is always active during and after reset unless user software change TESTMODE port register.
View ArticleApplication Kit TC2X7 - Flashing not possible after testing an example from...
Thanks for the answer! So, just to be sure i've understand correctly: - my TLF component is marked as TLF35584VS1, so the HW solution is not doable due to the A-step thing. - because of the constant...
View Article