Project randomly becoming "Unusable" ... App configurations (HW Connectivity...
What appears to be randomly, I had a project randomly become "unusable". It would no longer load properly. All the code was find, but App configuration was gone, specifically all the HW connectivity,...
View ArticleCRC_SW_EXAMPLE_XMC13 problem
Hi Rija, I think your question is different from Rijani's. Can you create a new thread for it? Are you using the XMC1200 boot kit + inLight white LED board? And is it possible to attach your test code?...
View ArticleProject XMC4800 for a migration from 100pin to 144pin
Hi, I have a project with EtherCAt and 4 channel SigmeDeltaDemodulator. While it is not possible on 100Pin a tried to change MCU on 144Pin: I got this error message: 'Building file:...
View ArticleClik here to view.
PWM Single shot mode
Quote: Originally Posted by swyoon Hi~~ Board : XMC1302 boot kit DAVE ver : DAVE4.0.0 I tried to make PWM_CCU8 single-shot mode function enable Attachment 2207 step1 : single-shot mode -> change...
View ArticleXMC4500 ETH-Problems with httpserver_raw-example
Hi, Do you think it would be helpful if you try the lwIP forum? As I have limited knowledge on the stack which I am also trying to build my knowledge n experience while working on this. So sorry about...
View Articlehow to use the ambient light sensor(XMC1200 RGB LED Light)
Hello , Is there any example or DAVE component how to use the ambient light sensor? regards , Allan
View Articlehow to use the ambient light sensor(XMC1200 RGB LED Light)
Hello , Is there any example or DAVE component how to use the ambient light sensor? regards , Allan
View ArticleHigh side switches reverse battery protection
HI I think something may be wrong with the resistor Damon ______________________________ automaty SMT
View ArticleClik here to view.
Sample programs (Beginner programs) for AURIX TC27x
Quote: Originally Posted by vk18434 Hi, Do we have any sample c programs for AURIX TC27x tricore architecture ? The programs should basically have led toggle, timers, ADC, SPI etc. Please guide me....
View ArticleClik here to view.
EBU to control LCD
Thank you for your answer. Right, I understand that. What got me thinking was this section: Attachment 2210 This means that I cannot use the SDRAM interface directly, but I can still use the EBU to...
View ArticleClik here to view.
XMC4500 PMU PFLASH IDLE Behavior
Hi folks, I have been experimenting a lot with the XMC4500 recently and stumbled upon something very confusing. Apparently, there the FLASH0_FCON.IDLE bit has a weird and unexpected performance impact....
View ArticleFirmware Update over External Memory
Hi, Anyone please help me in above implementation. Thanks & Regards, M. Ramarao.
View ArticleBootloader running from Flash
Hi, I am currently working on XMC1400 Dev.Kit. Please guide for Boot loader implementation for external memory. Thanks & Regards, M. Ramarao.
View ArticleFAQ for XMC4800 EtherCAT
Hi, Refer to the first reply to thread which is being updated per the queries on the thread.
View ArticleMeaning of the rwhis bitfield
Not sure what device you are working with, I have never seen an 'i' before. Search your user manual for "Bit Function Terminology". The other letters are: r - read w - write h - hardware, can be...
View ArticleHow to store XC2723X results of 10 analog channels? There are ony 8 result...
The XC2723X has 10 analog channels. But the number of result registers are only 8. If I would like to use scan conversion for all analog channels, how can I store the result of all analog channels in...
View ArticleEthernet driver issue with Application Kit TC275
I have some problems with regard to the Ethernet driver. My device is Application Kit TC275. When I use the function Eth_17_EthMac_ReadMii(...) supported by Mcal's function to read a transceiver...
View ArticlePWM 8 phase shifted signals
Hi Milad, I am genuinely glad this helped! And no problem, hope you had a great vacation! It sounds like there should be a way for you to configure the timers to your needs - it just takes a bit of...
View Article