BSDL file for XMC4500-F144K1024
Can you please provide a BSDL file for the XMC4500-F144K1024? I need this file to generate boundary scan tests for my board. Many thanks
View ArticleProblems with FIFO/Gateway on XMCs 4400 Multican
Hello, we built up a gateway with an XMC 4400 between Can Node 0 and 1. Gateway is in both directions, all messages from Node 0 to Node 1 and from Node 1 to Node 0. Therefor we have on RX MO on Node 0...
View ArticleLooking for XMC 4500 UART App example code
Is there a newer version for Dave4 for this XMC4500 UART example? Or is there a good application note describing how to initialize UART communication on specific pins? The user manual to read is a...
View ArticleError occured while connecting to the solver process
I meet this question too,and the forum gives a solution "Error Message2: Error occurred while connecting to the solver process 1. Connection to solver process failed - communication problem, TCP port...
View ArticleCritical BUG in XMC Chip of the CAN Tx-Fifo
Hello. I've build a CAN Transmit Fifo, to send out CAN frames over a gateway to a second Can-Bus. This is working fine in normal case. But if there is the smallest little problem on the side with the...
View ArticleUpdate XMC1200 Application via ASC BSL
Do i understand it right, that if i want to update my application in the flash using the ASC BSL, i have first have to load a loader software into the RAM via ASC BSL. And after that loader software...
View ArticleBest Academic Writing Service From Expert and Dedicated Writers
Thanks for sharing Interesting post. Thanks for taking this opportunity to discuss this, I appreciate with this. If possible, as you gain information, please update this blog with more information. I...
View ArticleHow to work with influencers?
Influencers are everywhere. So much so, theyre now a mainstream marketing avenue. When collaborating with influencers how you work with them is as important as who you choose to work with. Influencers...
View ArticleXMC4500 Relaxkit lite QSPI flash not working
Hello, I have exactly same issue, but porting the example that works on the Hexagon to Relax Kit did not help. See this post : https://www.infineonforums.com/threa...5803#post15803 Can someone post an...
View ArticleGate Driver selection for 80V TOLL MOSFETS
Hi everyone, i have to design 3 phase inverter to drive induction motor. Input is directly connecting from the battery of 80V and 300A rating so i choose 80V 300A OPTIMOS POWER TRANSISTOR IPT012N08N5....
View ArticleHow to change slave select pin from high to low in SPI_MASTER_APP
Hi, I am new to DAVE programming. I am using SPI_MASTER_APP to send data to two slaves. Each time I have to send data, I have to make slave/chip select pin low, send data and then pull it back high...
View ArticleSPI_MASTER App with more than one slave select lines
Sorry i have a related but different question. If I want to change the port_config from high to low and back again (the slave works on low CS), how do I do that in coding? I tried like this but...
View ArticleClik here to view.
SPI Flash on XMC4500 Relax kit
Sorry i have a related but different question. If I want to change the port_config from high to low and back again (the slave works on low CS), how do I do that in coding? I tried like this but...
View ArticleTASKING LSL File for BootROM
Hi, I'm writing an application that will be sent in Boot mode to TC17xx, my problem is to understand very well how LSL file is working (I have read the PDF documentation) The error I have it's...
View ArticleLWIP eternetif.c driver latest status
Hi, The latest version is available in the latest update. regards, Jesus
View ArticleClik here to view.
Ethernet XMC4500 Relax Kit
Hi, Find attached the tcpecho_raw example using the ETH_LWIP APP. Regards, Jesus ????? LWIP_TCP_ECHO_RAW_XMC45_RELAXKIT.zip (6.17 MB)
View ArticleXMC4800 EtherCAT APP Debug Error
Hello, I am new to Infineon Forum, so feel free to correct me if I violate any forum rules :) I am using the XMC4800 Relax EtherCAT Kit with DAVE (4.3.2) and Beckhoff SSC. I was going through the...
View Article.icf Linker script for Example Application XMC1000-SW Update using ASC
I have tried the example Dave4 applicaiton example for updating an XMC1000 using ASC ( https://www.infineon.com/dgdl/Infine...b5e955bcf&sd=t ) It works quite well, using all applications in Dave....
View Article