IRLB3813 Occasionally failing upon battery insertion
I have successfully used the IRLB3813 in numerous portable power tool designs to drive PM brush motors in the 450W range. All these tools are powered by LiPo 18V nominal 20.5V max removable batteries...
View ArticleLWIP eternetif.c driver latest status
Hello, there are many APPs and example projects shipped with Dave for XMC devices which have Ethernet Interface. I could see that over the years several modifications are introduced to the driver. What...
View ArticleXMC1400 Boot Kit SWO with IAR
I'm trying to use the function profiler feature of IAR Embedded Workbench. I get no data. It relies on SWO from the board. Does the XMC Boot Kit support SWO?
View ArticleClik here to view.
TC277 board, debug port secured
Hello, I'm debugging the TC277 with Trace32, I'm testing the Standby mode of the MCU, after I set it to the standby mode, the Trace32 is down, and I tried to download again, it's debug port secured....
View ArticleAngle definition in the MOTOR_LIB
Hello I'm looking for a definition of "int16_t angle" argument in the method: int32_t MOTOR_LIB_ParkTransform (int32_t i_alpha, int32_t i_beta, int16_t angle, int32_t *iq) What unit is used there and...
View ArticleNo source availble for GDB
Hi Vinay, A brief reply, as I'm typing from my phone. But just in case helps, I get that error if an interrupt occurs, but there is no corresponding entry in the vector table. So just to rule that out,...
View ArticleVoltage monitoring
Hello, In looking through the reference manual, I couldn't find enough information on the Power Management system regarding the VDESR flag outputs. I have tried the following for checking the voltage:...
View ArticleDAVE IDE 4.3.2 not responding on Win 8.1 64bit
Hi everyone, is a solution to an unresponsive / frozen DAVE IDE right after first time start-up known? After a clean and first time install of DAVE on Win 8.1 64bit the IDE becomes unresponsive after...
View ArticleConnection closed by the GDB server - no source available for "0x0"
I first ran into the issue (no source available for "0x0"), when I tried to compile a project from a co-worker. After some investigation, I found the issue can be reproduced even if I use the default...
View ArticleClik here to view.
How to get K value in the PID controller
Hi,I am using XMC1400 for my interleaved PFC.I am referring to the application note from the infenion for my controller design.While designing the PID controller,I have a doubt.My doubt is how to...
View ArticleXMC1400 - Enable debug interface for ASC BSL mode with time-out (ASC_BSLTO)
Hi, As far as I understand:When using BMI User mode with debug enabled (UMD), the debug interface is configured and enabled at the end of the Start-up software(SSW) execution. So, the user can debug...
View ArticleSPI based micro SD Card interface
Hi, working on SD card example below http://www.keil.com/appnotes/files/apnt_273.pdf with different IO pins for SPI Interface of Micro SD card with XMC4700 unable to write data on micro SD Card. the...
View ArticleDithering effects multi-channel synchronization, why?
I am using a XMC4500 for a 3-phase BLDC Motor control application. My Setup is taken from the application notes. I have the POSIF0 to sense the hall sensor Inputs and a CCU4 timer slice for the...
View ArticleHardFault_Handler while operating flash(NVM)
I was trying to use flash to simulate eeprom and get an example from keil examples. but the examle didn't work. I look into the debug and find out that whenever operate with the flash address ,the...
View ArticleE_EEPROM_XMC4 breaks linker_script.ld
I am using DAVE 4.3.2 with all the APP updates. I added E_EEPROM_XMC4 and it rolled back the linker_script.ld file. The project compiles but no longer works. Before the APP addition, the ld file was...
View ArticleKIT_AURIX_TC277_TRB Chip corruption
I have KIT_AURIX_TC277_TRB evaluation kit but currently I have a problem that the microcontroller is locked due to UCB write sequence error, so I need to change the microsontroller with a new one, on...
View ArticleDownload Infineon MC-ISAR
Hello, I can't find where I could download Infineon MC-ISAR MCAL drivers for AUTOSAR, I have searched inside Collaboration platform, but managed to find only user manuals.
View ArticleSAL-TC222-16F133N Power consumption sheet
Hi, Can someone share the power calculation sheet for this controller (SAL-TC222-16F133N)? It is not clear from the datasheet how much current has to be supported on 5V and 3.3V supply inputs. This...
View ArticleADC auto scan example
Dear, I also use a XE167FM, I want to read input P15.0 to P15.6 but it's not working. I change the input at each timer. When I read only one input it's ok, but if i want to read 15.0, 15.1 the next...
View Article