Clik here to view.
Absolute Maximum ratings of RF Devices
Quote: Originally Posted by BradP01 Hi, Can someone offer some insight please relating to absolute maximum ratings of RF devices? I outline an RF FET case study below: Absolute maximum rating from...
View ArticleCAN Interrupts somehow stop happening
Working with the XMC4500 chip, I have two CAN Nodes setup and they have multiple MOs to transmit/receive data. Connecting the XMC4500 to a high load bus (>60%) if there is some Error Frames, at some...
View ArticleClik here to view.
XMC Library and Segger Embedded Studio for UART with XMC4700
Hello, I am using Segger Embedded Studio and would like to build a simple UART communication for a XMC 4700 (got the eval board XMC 4700 Relax Kit). I found instruction on how to use the XMC Library...
View ArticleDual TLV493D Sensor Help
You are using dual TLV493D. You have set the ADDR/SDA of both devices on I2C correctly? On power-up the TLV interprets the applied voltage level on ADDR/SDA pin as logical “0” or “1”. This determines...
View Articlequestion of XMC4800's flash protect
Hi: i m using the XMC4800 to develop the EtherCAT slave, the chip is XMC4800-F144x1024. now i want to set a flash protection to protect the flash sector. i have already found the funtion of...
View ArticleClik here to view.
SPI Flash on XMC4500 Relax kit
Hello, I am using Dave 4 with latest Dave apps available. Great tool ! I try to use the Serial SPI Flash available on XMC4500 Relax Kit. I take the example of XMC4500 Hexagon, and change The MCU model...
View ArticleSense2GoL Implementing FMCW
Hello, I am trying to implement FMCW for Sense2GoL and I have trouble figuring out how to access DAC in order to give VCO different voltages with it. Which library to use and which pin should I...
View ArticleXMC1400 - Running from the standby clock (32kHz DCO2) after deep sleep wake-up
Hi, The maximum recommended is 4 times the frequency of DCO2 to prevent a sudden load change that could cause a brownout reset when entering sleep or deep sleep mode. Actually I would go down to 32KHz....
View ArticleXMC1400 - Maximum MCLK/PCLK frequency before going to deep sleep mode
See https://www.infineonforums.com/threa...ll=1#post15805
View ArticleXMC1400 Math Coprocessor - poor performance
I'm seeing another anomaly. I get the same results when I configure the pclk for mclk*2 as I do when I configure pclk for mclk. I configure the clocks by defining the data structure below and calling...
View ArticleExample for temperature sensor
it still hangs on XMC1300. Am I missing something here? Seems like the ROM address in the library might be wrong. FYI both XMC_SCU_CalcTemperature and XMC_SCU_SetTempHighLimit function hang. EDIT: For...
View ArticleClik here to view.
MOSFET Rdson simulation problem.
We widely use simulation with Infineon MOSFET models as they are very accurate. We are using Simetrix/SIMPLIS simulator. But recently I found* a very strange behaviour of MOSFET Rdson at the...
View ArticleSense2GoL Pin description
Hello, I have tried finding pin description for the 9 pins located on the board. Can somebody tell me how they are connected or tell me where can I find a description? I have only found pin description...
View ArticleUSB HID + Windows 10
Hi! I found the problem. Windows 10 does not allow the device to be registered as USB 1.1 protocol. Changing to the following in the device descriptor solves the problem: Code: .USBSpecification =...
View ArticleTLE 6244X Overvoltage Flag
Hi Richard Li, The power supply voltage is OK. Which bit of the StatCON Register is set? Is it Bit 4? The STATCON_Register is used by the over-temperature detection. Have a look at chapter 4.5. of this...
View ArticleClik here to view.
SPI to Memory transfer (PGDMA)
Hi, Thanks for the files and information. I have tested the application. There is one problem, that the data is not sent at end of frame. It is sent at end of word as you can se en the screenshot....
View ArticleHow to change Dave4 PMSM-FOC app from sensorless to Hall ?
Dear rocky, you can manipulate the values PLL_Estimator.RotorSpeed_In and PLL_Estimator.RotorAngleQ31. This values are update in the FOC so you need to change them after the FOC call. Please consider...
View ArticleEthernet XMC4500 Relax Kit
Did you found a solution for that? I'm in the same Situation now and nothing to find. Anybody else? best regard
View ArticleDAVE 4 / XMCLib ethernet example.
Hi to all, there is still no example for LWIP with Dave apps. I need some send and receive orders here.
View ArticleGetting started with KIT_XC2224L_SK
Dear all, i am new to infinion family. I have previously worked with AVR and Microchip MCUs. I am seeing Infinion has tries its best to make is user unconfortable. I have installed DAVE and i need to...
View Article