Do I Need two BTN8962A Here
How are you?:D Recently I am involving in a project about design a BDC driving board with BTN8962A which is from Infineon . BTN8962A is a half of H-bridge IC. As we all know,BDC driving circuit is just...
View ArticleTC29X USB3.0 => SRI External Bus Unit (EBU) ?
hi guys I use a TC297 Microcontroller and would like to connect the Controller via USB3.0. My Idea is to use the EBU interface, as the USB3.0 Transceiver has a 32 parallel Output or has anyone of you...
View ArticleEthernet problem solving on TC23x
MCLK is running in 25MHz, while the MDIO data is sent by 2.5 Mhz I see there is no synchronisation between the MCLK and MDIO data line. How it can be corrected
View ArticleAurix TC3xx code generation using embedded coder
Dear Friends, Good day! We develop features on simulink and use embedded coder to generate c code for autosar target. I want to optimize the generated code for performance improvement (computation...
View ArticleXMC1400: CCU concatenation with underflow in first slice
Hi, I am using CCU41 slice 1 to count an event. CCU41 slice 2 is concatenated with slice 1 (TCE bit in CMC). If the counting direction is "UP" everything works as expected. Example: slice 1 is at...
View ArticleHello Everyone, New member here
Hi, My name is Rechard Smith 34 years old! I'm new here in this fantastic community. I found this board on the internet. Infineon equipment and accessories are my first choice. We utilized too many...
View ArticleClik here to view.
Xmc4400 | pwm + dma
Hi, See attached modified main.c file to enable 16bit duty cycles and enabling interrupt that signals that a block transfer is finished. Regards, Jesus ????? main.txt‎ (4.8 KB)
View ArticleClik here to view.
Micrium uC/Probe for XMC 2go XMC1000 - Oscilloscope
Hi, Alternatively you can use the UCPROBE APP from the contributed APPs repository (Help > Install DAVE APP/Example/Device Library ...) Attachment 3163 Regards, Jesus ?????...
View ArticleClik here to view.
How to give the master a random and a short address to my slave device?(DALI...
Yes, I understand, but all the screenshots that help to understand the essence of the problem and my reasoning are not loaded onto the post. In addition, there is a message that this post should check...
View ArticleTC29X USB3.0 => SRI External Bus Unit (EBU) ?
hi guys I use a TC297 Microcontroller and would like to connect the Controller via USB3.0. My Idea is to use the EBU interface, as the USB3.0 Transceiver has a 32 parallel Output or has anyone of you...
View ArticleClik here to view.
How to give the master a random and a short address to my slave device?(DALI...
Yes, I understand, but all the screenshots that help to understand the essence of the problem and my reasoning are not loaded onto the post. In addition, there is a message that this post should check...
View ArticleTC29X USB3.0 => SRI External Bus Unit (EBU) ?
hi guys I use a TC297 Microcontroller and would like to connect the Controller via USB3.0. My Idea is to use the EBU interface, as the USB3.0 Transceiver has a 32 parallel Output or has anyone of you...
View ArticleCapture APP reset
Hello, i am using the CAPTURE APP in DAVE 4.3 to measure the timer ticks/time between the rise-to-rise edge. CAPTURE_GetCapturedTime(&CAPTURE_0, &captured_time_ticks); My Problem is, that i...
View ArticleClik here to view.
Matlab XMC Library for Embedded Coder Problem
Hi Pessara, Did you find any solution? I have also the same problem, although the program was working several months ago. Do you also use windows 10? I guess the problem comes from some missed .DLL...
View ArticleClik here to view.
XMC4800 CCU8 synchronized start does not work
Hi, The attached project Shows how to configure the PWM_CCU8 APP to achieve the synchronous start of the timer slices using the GLOBAL_CCU8_SyncStartTriggerHigh() function (see main.c) Regards, Jesus...
View ArticleXMC4200 SPI Change SELO pins during program execution
Hi, Did you try something like below? SPI_MASTER_EnableSlaveSelectSignal(&SPI_MASTER_0, SPI_MASTER_SS_SIGNAL_0); SPI_MASTER_Transmit(&SPI_MASTER_0, data, DATA_LEN);...
View ArticleCan't find how to do sensored FOC
Hello, We are evaluating XMC4000 for an encoder sensored motor drive. We need some information about the PMSM_FOC_EXAMPLE_XMC44 Dave code. - Is this example intended for production use, or is it only...
View ArticleATTENTION: Update your SEGGER JLink version to latest version (V6.20a as of...
BE CAREFUL If you update Segger JLink version to 6.20e The difference is in the 'e' revision letter at the end. It seems that Segger guys have changed the location of JLink_x64.dll used by DAVE to...
View ArticlePWM_CCU8 module stops when debugging
Hi! I also have the same problem. I need to bring the PWM outputs into a safe condition. Read the GCTRL.SUSCFG documentation below Suspend Mode Configuration This field controls the entry in suspend...
View Article