Micrium error
I am trying to debug my code in micrium using .elf file. I am not able to locate Main.c file in that. Can anybody help me with this issue.
View ArticleFacing lstdc issue in HighTec IDE
Dear Support Team, I am using HighTec IDE for building MicroPython source code. I am facing following errors while building. c:/mingw/bin/../lib/gcc/mingw32/6.3.0/../../../../mingw32/bin/ld.exe:...
View ArticleXMC 4800 uC VADC performance with ALIAS
Hi all, I am using XMC 4800 for concurrent reading of three current sensing resistors. I was wondering if there is any different between using ALIAS to sample from any channel and specifically using...
View ArticleXMC4200 and printf function using CMSIS
Hello everyone, I'm an electronics student working on my first ARM project with a XMC4200 hexagon board. I use keil MDK5 as an IDE. I only have experience with the XC88 series programming in assambler...
View ArticleMeasuring 2 signals in parallel with XMC1100
In https://www.infineon.com/dgdl/Infine...4b078129f42271 you write on p 12/24:*In many occasions, algorithms request the usage of several analog values that are measured at the same time. As an...
View ArticleFacing "asm" related issue
Hello, I am using HighTec IDE for cross building of MicroPython source code for TriCore Architecture. I am facing "asm" related errors in building the source code. I added all required files to the...
View ArticleDave 4 - XMC4500 debug from program with offset
Dear All, I want to debug a Dave project to be downloaded with offset to the FLASH start. I.e., in XCM4500 the start address is 0x0C000000 and I want the application to be downloaded (and debugged) at...
View Article9-bit UART with XMC1200
Hi, is it possible to use a XMC1200 with: 1 Startbit, 8 Databits, 1 Modebit, 1 Stopbit = 11 Bits Is the Modebit the "Parity Selection" and which one have I to use: "Odd Parity" or "Even Parity"? Thanks...
View ArticleFeb, 27 2018: New Release of DAVE, DAVE APPs and other Libraries
Today we published new versions of DAVE, DAVE APPs, XMC Lib, Device Descriptions, and Device Support Pack. DAVE v4.4.2 New features:Board selection option introduced. Library store default path is...
View ArticleFeb, 27 2018: New Release of DAVE, DAVE APPs and other Libraries
Today we published new versions of DAVE, DAVE APPs, XMC Lib, Device Descriptions, and Device Support Pack. DAVE v4.4.2 New features:Board selection option introduced. Library store default path is...
View ArticleTLE9879 bootloader
Hi, any idea how to flash two hex files (bootloader and application hex) on TLE987x micro? I am using keil µvision 5. Is there from infineon any flash programmer tool for TLE987x? Another question,...
View ArticleAP32272 - AURIX Generic Bootstrap Loader Issue
Hello, Did anyone manage to use the Windows tool for flashing the Aurix microcontroller? I managed to get the supplied example hex file flashed. Also I managed to flash a basic project with just a...
View ArticleLPAC and HIB_IO_1 configuration with XMC4400
Hi, sorry for my mistake. Please replace "...is above the upper threshold level independant from the supplied voltage" with "...is above the lower threshold level independant from the supplied voltage".
View ArticleTLE493D-W2B6 enabling the wakeup feature?
Had a quick look. Configuration parity in the W2 device has to be calculated as: * all bits of i2c registers 0x07 to 0x0C * 7 LSB of i2c register 0x0D (so the WU enable flag is also part of the parity)...
View ArticleStation Management Interface for custom PHY (DP83822)
Hello everyone! I am implementing an Ethernet PHY for a custom mcu board using an XMC4500 and a DP83822. This Texas chip is compatible with the existing driver supplied by Infineon for the DP83848 phy....
View ArticleTLV493D returns NCK
The sequence "Start - 0x00 - Stop" (which is basically sending just the general call address 0 on the i2c bus) resets the sensor at the end of the frame. Is SDA on low on intention during start-up? The...
View ArticleClik here to view.
TLV493D acknowledge problem
In your schematic you have not shown the pin numbers. Just for clarification: The "main GND" is pin 3 on the sensor (see table 2 of the datasheet). If this is connected i2c should work already. even if...
View ArticleMCTROOL V2 with IRMCK099 and Eval-M1-05F310 board problem
Hi, I am in the same case, is there any news? Best Regards
View ArticleClik here to view.
Dave 4 - Not able to add APPs or device library
Hello everyone, I'm trying to add APPs to my projects but when doing it I get the error in the following picture. Attachment 3373 Then I tried to install the device library over Help -> Install Dave...
View ArticleIssue connecting TC27x board via miniwiggler
Hello All, I am trying to connect TC27x device with miniwiggler DAP, but i notice the following error Starting Debugger... The debug instrument IO could not be initialized. The GDI debug instrument...
View Article