Demodulate BMC-Signal using CCU4_Slice_Config app
Hi, Two alternatives: 1. You could assign the input signal to two input events, one that starts/clears the timer on both edges and the other one that captures also on both edges. In the ISR triggered...
View Articleproblem with update of version 4.4.2
Hi, Which update is DAVE trying to install? regards, Jesus
View ArticleDAVE CE "Break point Installation Failed: Unmatched Quote"
Hi, In the snapshot I see that you are trying to debug the release build. The release build does not contain any debug Information. Please change the Project build configuration to debug. Regards, Jesus
View ArticleExport DAVE to IAR - assembly file doesn't compile
Hi, Did you try https://www.infineonforums.com/threa...ll=1#post16067
View ArticleFAQ for XMC4800 EtherCAT
Hi, I have a question regarding the processing time of the ethercat stack. More specifically, where can I find test results involving the execution time (within a single cycle) of the beckhoff Ethercat...
View ArticleClik here to view.
IR3553 / IR3555 pin compatible?
Hi I have an out of warranty Graphics card I wish to attempt a repair on. The Card has died twice during it's warranty and again just after warranty ended (not your fault!), I suspect underpowered...
View ArticleNeed help with a Smps
Hello. For the past 2 months I've been reasearching smps , I need a dual rail +/- 35-50 V ,5 A with a input AC of 240V /50 Hz Can anyone point out the correct parts or some application notes so I can...
View ArticleXMC4500 multiCAN, getting MSGLST in a RXFIFO configuration
And still we are getting MSG_LOST a few times every day. (SW FIFO scheme) Unsure of what to try next. We have a FIFO high-water mark logging scheme and it never uses more than 1 MO. We have a test were...
View ArticleConditional compile over Build-Configurations
Hello Affordable holiday packages in India and International Holiday Packages HolidayHai, get amazing deals and best experience at the cheapest price ______________ HolidayHai
View ArticleFOC Sensorless questions and thoughts [Case:3760197]
Hey atena, Looks like this forum is not supported enough, I have had similar questions about FOC, and more specifically sensored FOC, but with no answer. The behavior you see is a result of sensorless...
View ArticleTLE5012B E1000 with Arduino Mega
Hi ManikantaRaju, Did you ever get this sensor to work?
View ArticleBTS7960 Capacitor Blown
Hello guys, I got a H Bridge BTS7960 to use as a motor driver on a project. When testing it with my 12V 800W DC motor and a Arduino, the capacitor on the bridge blew up even though the current measured...
View ArticleVADC Mesaurement affected by ISR?
I observed some strange behaviour of an XMC4800 that I cannot understand: My situation: PWM-ISR (16kHz): - Read ADC results - Trigger new ADC Conversions Init-Function(): - enable 'ADC-Conversion...
View ArticleExternal Interrupt from an IO-Pin
Hi all, I will you use three IO ports as external interrupt sources and have configurated them with IO002 App (DAVE-3). Each port should support a separate Interrupt source, so I have created three...
View ArticleLEDTS for XMC1200
Hello Juergen, You could send me this example on my email rodrigo@eaglewingd.com. And another because it does not have an example of how to use this peripheral in DAVE4 ??? Thank you so much
View ArticleXMC1000 TIP of the day: Software TRAP for CCU8
It works. I have to say it is a little complicated to do such configuration, going through the whole datasheet really time consuming.
View ArticleROM Library Functions for SP37T Tire Pressure Sensor Module
I am using Keil IDE for software development for SP37T tire pressure sensor module. When compiling the code, the header file SP37T ROM Library.h is not available. Where can i get this header file? Any...
View ArticleClik here to view.
Incorrect external interrupt trigger
Hi all, I have configerated an IO ports as external interrupt source and have used the IO002 App (DAVE-3). The signal is connected via a EUR001 instance to the NVIC. Attachment 3508 In ERU001 App I can...
View ArticleErrors in XMCLib
Hi, i am using DAVE 4.4.2 for the XMC4400. I got a compiler error in the header file xmc_ccu8.h, when i compile my application with the Debug configuration. Here is the source: Code: __STATIC_INLINE...
View ArticleTLE9879 Cortex M3 reset behavior
Hello, I'm developing a custom embedded board with TLE9879, which works fine with the debugger attached. Yet, it's not always working when I'm running it stand-alone, whereas it does work stand-alone...
View Article