Get current system clock time
Hello , I am using infineon tricore tc299tf , i have initialised the STM module and now want to create an interrupt using STM compare registers but everytime i try to run it I am getting a TRAP 4 tin 3...
View ArticleFail uploading hex file using SP37 programmer
I am using Keil IDE for programming sp370 pressure sensor IC. Once the project created, when uploading hex file using sp37 programmer, the following message occured. ADDRESS OUT OF RANGE FAILED to...
View ArticleSPI slave MISO line issue (XMC4500 + XMC1201)
Hi Sebastian, hi Min Wei, I have the same problem with a XMC1402. How did you solve this? 1) How can you enable/disable the slave MISO line? 2) PDL can only be set to 0 (the passive data level is 0) or...
View ArticlePG-DSO-12-17 3D Model for IFX9201SG
Hi, I'm looking for 3d Model in STP File for PG-DSO-12-17. Many Thanks Ying
View ArticleSPI slave MISO line issue (XMC4500 + XMC1201)
Hi Sebastian, hi Min Wei, I have the same problem with a XMC1402. How did you solve this? 1) How can you enable/disable the slave MISO line? 2) PDL can only be set to 0 (the passive data level is 0) or...
View ArticleXMC ECAT0 Alias
I want to check or change the Station Alias. However, it seems that the correct information can not be read or changed through the defined ECAT0. Are there other conditions or procedures for use? ECAT0...
View Articlehow to clear the buffer full in UART
hello, I am also having this issue on same device and configuration. I am using both channels. Can anyone give solution? Thanks.
View ArticleSP370 IC Selection on Keil IDE
I am developing a project using Infineon IC SP370. It has in-built 8051 microcontroller. I am using Keil IDE to develop the code for this chip. When creating a new project, for chip selection, this...
View ArticleAurix 2G Free Entry Tool Chain Interrupt on all cores
Hello, I am working on tricore tc299tf and trying to initialize system timer interrupt. I have tried to use the examples that are explained here however my timer interrupt is still not working...
View ArticleClik here to view.
BTS6143 Max FET Voltage
The data sheet shows the BTS6143 max voltage to part of Vbb = 38 volts. During a turn off cycle of an inductive load ,the output clamped voltage is limited to Von(CL) -42 volts. Is the drive FET rated...
View ArticleClik here to view.
Flasher for TLE9879
Hi. What program from infineon can I use to program tle9879? J-Flash from Segger, and Evalkit TLE9879 are not friendly, and require a license. Attachment 3511 ????? Clip.jpg (196.7 KB)
View ArticleProblems with FIFO/Gateway on XMCs 4400 Multican
By using gateway with FIFO (RxMO an gateway source side, TxFIFO MOs an gateway destination side) two pointers must be initialized - pointer (defined via MOFCR register in the RxMO) for gateway feature...
View ArticleXMC4500 multiCAN, getting MSGLST in a RXFIFO configuration
By using gateway with FIFO, normally one message object is configured as RxMO on gateway source side, and a couple of message objects are configured as TxFIFO MOs on gateway destination side. the 4...
View ArticleNo confirmation email for Dave download
Hi, I had the same problem when using Firefox 56.0.1 (64bit), solution was using Microsoft Browser.
View ArticleSwitch from 1767 to 1782
Hi I have a Tricore AUDO board which I upgraded from a TC1767 to TC1782 by replacing the processor and TLE7368-E I appear to be able to get my code running after commenting out the initial...
View ArticleProduct Information
Dear Community, Please find here all information of the automotive products in NovalithIC family. Visit us @: Product overview: https://www.infineon.com/cms/en/prod...ridge-driver/# BTN8982:...
View ArticleImplementing RDM over DMX-512
Hi, I'm also a newbie to the XMC series. What did you do to get RDM support working?
View ArticleSPI slave MISO line issue (XMC4500 + XMC1201)
Hi Juergen, 1. You enable/disable the MISO pin at the slave by configuring the pin as input/alternate ouput. Code: // enable MISO XMC_GPIO_SetMode(MISO, XMC_GPIO_MODE_OUTPUT_PUSH_PULL |...
View ArticleErrors in XMCLib
Hi, Thanks for reporting the issue. It will be fixed in the next release. Regards, Jesus
View Article