Clik here to view.
Questions about phase inductance and phase resistance in FOC Code [SOLVED]
Quote: Originally Posted by Mc-Key Hi Rocky, The FOC democode is expecting the motor windings in a star connection. Answering your questions: 1) Yes, the Phase resistance is half of the Line to Line...
View ArticleIRPS5401MTR tools
"Register Map" tab is absent in last builds of PowIRCenter software(6745 and 6774). Is the previous builds with this tab (e.g. build 6200) completely support IRPS5401 R3(00FC:0x0352)? Is the Excel PI...
View ArticleUsing SMU as Watchdog Triggering machine during Bootloading
This is writer and using SMU as External watchdog trigger machine is possible. Thanks !!!
View ArticleTC275 watchdog does not work
Hi I am using TC275 evaluation board and the sample code along with the board. this is cpu0 start-up driver and I remove those lines that disable both CpuWatchdog and SafetyWatchdog. So basically...
View ArticleTC275 IEEE 1588 Time Stamping(EtherNET)
Hello. how can used IEEE 1588 Time stamp in TC275? i already set the fine update time stamp mode(EtherNET). also set (TTSE, IC,FS,LS,TCH) pins. but i can't get exactly time stamping when send or...
View ArticleEnable LockStep Mode
From the manual: Quote: These registers are only initialized by a cold power-on reset. In this initialization state, all lock stepped processors in the system will have lockstep enabled. The lockstep...
View ArticleTC275 IEEE 1588 Time Stamping(EtherNET)
Hello. how can used IEEE 1588 Time stamp in TC275? i already set the fine update time stamp mode(EtherNET). also set (TTSE, IC,FS,LS,TCH) pins. but i can't get exactly time stamping when send or...
View ArticleClik here to view.
Clock Shaper - what is it?
"shaper" is talked a lot about in the reference sheet and datasheet for the XMC1400. No where I have found is it explained what it actually is / does. A little help please? A link to the documentation?...
View ArticleXMC1300 pure sine wave inverter
I am very interested in this issue too. Please, some experienced user could help?
View ArticleDoubts with non connected pins of XMC4800 microcontroller
I don't know on the XMC4000s, but a lot of datasheets will either specifically say to leave non-connected, or common knowledge is to tie them either to ground or power. You don't want a floating input,...
View ArticleXMC1400 Keil can't read some SFR / Registers, mapping error?
Added development. It seems when using SEGGER JLINK (the one on the board) that memory outside of certain regions does not READ. Attachment 3563 Reading 4000'0300 (SCU_CLK or something around it) for...
View ArticleRegarding Interrupts
Hello.. I am using XMC4800 microcontroller. I want to generate an interrupt from FPGA to XMC which is a hardware interrupt. My question is, is it ok to connect the interrupt to ERU0 unit of the...
View ArticleRegarding Interrupts
Hello.. I am using XMC4800 microcontroller. I want to generate an interrupt from FPGA to XMC which is a hardware interrupt. My question is, is it ok to connect the interrupt to ERU0 unit of the...
View ArticleTC275 IEEE 1588 Time Stamping(EtherNET)
Hello. how can used IEEE 1588 Time stamp in TC275? i already set the fine update time stamp mode(EtherNET). also set (TTSE, IC,FS,LS,TCH) pins. but i can't get exactly time stamping when send or...
View ArticleTC275 IEEE 1588 Time Stamping(EtherNET)
Hello. how can used IEEE 1588 Time stamp in TC275? i already set the fine update time stamp mode(EtherNET). also set (TTSE, IC,FS,LS,TCH) pins. but i can't get exactly time stamping when send or...
View ArticleTC275 IEEE 1588 Time Stamping(EtherNET)
Hello. how can used IEEE 1588 Time stamp in TC275? i already set the fine update time stamp mode(EtherNET). also set (TTSE, IC,FS,LS,TCH) pins. but i can't get exactly time stamping when send or...
View ArticleFLASH003/writing to flash in DAVE 4.4.2?
Hi, I'm trying to write a custom bootloader for an XMC1302-200 and don't have much idea where to start. (I don't think ASC BSL works because SRAM is only 16kB, and the program I'll need to be loading...
View ArticleTC275 IEEE 1588 Time Stamping(EtherNET)
Hello. how can used IEEE 1588 Time stamp in TC275? i already set the fine update time stamp mode(EtherNET). also set (TTSE, IC,FS,LS,TCH) pins. but i can't get exactly time stamping when send or...
View ArticleAHB bus interface: Priority DCode vs ICode
The ARM Cortex-M4 Reference Manual states in section 2.3.1 Bus Interfaces: Quote: ARM strongly recommends that any external arbitration between the ICode and DCode AHB bus interfaces ensures that DCode...
View ArticleCalculating der CRC32 by external program
Hi, I found here: "https://www.infineonforums.com/archive/index.php/t-2114.html" an example written by user freyes on Oct 13th, 2015, 01:30 PM, which seems to be near the method realised on the...
View Article