Could not install DAVEApps
I also have same kind of problem while installing, at the last moment it was showing Missing DD file in the zip. I think Update_Site_PACK_2016-05-17 version will solve that problem but unfortunately I...
View ArticleGcc version 4.9.4 vs. 4.6.4
"the same project" means not only code but also settings/optimazitionItems... are all the same.
View ArticleXMC4800 Relax: Dataflash example (SPI)
Hello, I tried to access the local data flash N25Q03 built into XMC4800 Relax board. Because there's no example for the 4800, I created a new SPI Master application with DAVE, then copied the required...
View ArticleClik here to view.
XMC4800 Relax: Dataflash example (SPI)
Below are osci shots with low speed 76800 Baud (working) and higher speed 115200 Baud (not working). It seems the XMC has some auto-chip select feature, which kicks in with higher speeds and de-selects...
View ArticleXMC4800 Relax: Dataflash example (SPI)
The problem was in configuration routine. Following line Code: XMC_SPI_CH_DisableFEM(XMC_SPI2_CH1); needs to be replaced by Code: XMC_SPI_CH_EnableFEM(XMC_SPI_CH_EnableFEM); To set "Frame End Mode" to...
View ArticleGTM VRS engine driver
Hi all. I found the documentation of the Step C of the GTM VRS Engine position driver but only the example code of the Step A. Has someone any idea of where can I find the Step C code? Thanks, GB
View ArticleMultiCAN+ gateway with transmit FIFO on TC277
Hello, I try to implement a gateway with FIFO on a TC277 but I encounter a problem. I have set MO10 to receive a CAN frame on CAN 0 and transmit it to the CAN 1 using a FIFO with MO4, 5 and 6. I set...
View ArticleDAVE TIP of the day: How to change the MCU for a DAVE project?
I has the same doubt. I found the answer over the link: https://www.infineonforums.com/threa...r-info-in-DAVE By the way, it is not possible to migrate (for example) from XMC1402 to XMC1302.
View ArticleBest printer for the study purpose
I want to buy a printer which will help to print the study materials. From outlook support, I get various kinds of the printer. I can't take the proper decision which one should I buy for the study...
View Article1-Wire interface
hi Andi, can you also email to me the example for DS18B20. Im currently using xmc1400 boot kit. Will it be compatible with xmc1400? thank you
View ArticleTLE9180D Current measurement problems
Hi there! I have a TLE9180D 3 phase bridge driver in communication with an Aurix TC234. I followed the power-up sequence of the bridge driver, and everything seems to be fine. All the error flags are...
View ArticleClik here to view.
Triboard TC277TF
Hi 1. Not able to flash into TC277TF board using UAD pro 2 debugger Attachment 3598 PFA of the failure report What is the issue? 2.Can i get the bootmode header for flashing into the Tricore Tc277Tf...
View ArticleClik here to view.
DAVE Webcast - Getting started
DAVE Webcast - Getting started (see DAVE4 project attachment) Install DAVE IDE for XMC microcontrollers 1. Browse to DAVE software download 2. Register and select the DAVE package you would like to...
View ArticleClik here to view.
MCDS Trace Viewer
Hello, I have measured the execution time of my program using: 1) Software cycle measurement followed by division of clock frequency --> #cycles / f_clk 2) Counting Ticks in the MCDS trace viewer...
View ArticleXMC ECAT0 Alias
Hi, is there any updates from Infineon regarding this matter? We are trying to update the SII in the eeprom and ran into some problems. I guess if the EEPROM reload and write is not setup in MainInit,...
View ArticleXMC 4500 SPI trigger transfer extern
Hi, Please have a look to the ERU_EXTINT example in the XMCLib distribution. Regards, Jesus
View ArticleClik here to view.
PROBLEMS with the XMC4800 EtherCAT APP SSC Slave Example
Hello at all, I have two problems with the XMC4800 EtherCAT APP SSC Slave Example. I use the following demo board: https://www.infineon.com/cms/de/prod...relax_ecat_v1/ and following programs: DAVE...
View ArticleHotkey for "Build project"
Hello, I tried to assign a hotkey (F8) to the Main Menu item "Project -> Build", but it doesn't work. Is there any other way than using "Window" -> "Preferences" -> "General" -> "Keys"...
View ArticleXMC1100 CCU4 Slice 0 and 1 interrupts switched?
I'm facing some strange behavior when implementing timer interrupts on the XMC1100 (XMC1100T016X0064) Using DAVE, I selected a Manchester decoder on Slice 0, and a 1 millisecond timer on slice 1. All...
View Article