Stopping slice timer via an event
This is a lot more relevant, actually: VADC.G0BFLOUT0 O VADC.G1REQGTK VADC.BGREQGTK CCU41.IN0L CCU80.IN0I CCU43.IN0H looks like CCU80 can then use external input I to trigger an event to stop the timer.
View ArticleCleanflight version of Infineon Multicopter
Smartphone App for Android is missing.....I have a LARIX ,but it have too little information.can u give me more information?
View ArticleClik here to view.
XMC1400 Keil can't read some SFR / Registers, mapping error?
Hi, I was able to reproduce your issue. Although only in Keil MDK, using Ozone from Segger (which uses the same SVD file) the correct content of the registers is displayed. Attachment 3585 It seems...
View ArticleDistance2go - Radar GUI device not showing up
May you please provide a screenshot of the device manager. Please be aware that the Distance2Go kit has 2 USB connectors as described in the Guide. The one going to the debugger part and that is used...
View ArticleSense2Go2 Firmware
Hi, the Software for this board is available via web download. Please follow the steps below for getting access: 1. Please complete new user registration:...
View ArticleRegarding Interrupts
Hi, You will need to use a XMC pin which can be routed to the ERU. Regards, Jesus
View ArticleTC277 JTAG locked
I expect you use the Infineon Memtool for programming. Without access to P14.0/1 I think there is no way to remove the device from Bootstrap Loader mode. If possible replace the device.
View ArticleAHB bus interface: Priority DCode vs ICode
Hi, Yes, the XMC4500 follows the ARM recommendation. Regards, Jesus
View ArticleXMC Link + XMC4500 F100
Hi, The XMC Link documentation states: Quote: 2.3 Power supply XMC™ Link is powered from the Micro USB plug and typically draws about 70mA. The on-board voltage regulator IFX54441LDV33 generates the...
View ArticleTC223 Starter Kit UART over DAP
Any UART over DAP don't exist. The miniWiggler and also the on board wiggler are using an FTDI device with 2 channels. 1 channel is used for DAP/JTAG the other one for UART. On board there is a direct...
View ArticleClik here to view.
Ping failure with RTOS in XMC4500 when power up
Quote: Originally Posted by jferreira Hi, In file Libraries/XMCLib/src/xmc_eth_phy_dp83848.c, in function XMC_ETH_PHY_Init() replace Code: /* PHY initialize */ int32_t XMC_ETH_PHY_Init(XMC_ETH_MAC_t...
View ArticlePartial Networking CAN transceiver
Have you already read this document AH1309_v1_1_Application_Hints_TJA1145.pdf? The wake up from the CAN bus is configured by the transceiver and generally would enable the power supply for the AURIX...
View ArticleClik here to view.
Using infineon models in Orcad
Hello, I am trying use the simulation models of the ir2010 driver and irfb4321 mosfet in OrCAD. Both devices show the same problem during simulation: ERROR -- Convergence problem in transient analysis...
View ArticleClik here to view.
Using infineon models in Orcad
Hello, I am trying use the simulation models of the ir2010 driver and irfb4321 mosfet in OrCAD. Both devices show the same problem during simulation: ERROR -- Convergence problem in transient analysis...
View ArticleClik here to view.
how to use memtool to program SAF-C165-LM HA 's external flash?
Quote: Originally Posted by cyhu0215 I didn't see any option for C165-LM in memtool? How? just use FLASHit toolï¼
View ArticleDistance2go - Radar GUI device not showing up
May you please provide a screenshot of the device manager. Please be aware that the Distance2Go kit has 2 USB connectors as described in the Guide. The one going to the debugger part and that is used...
View ArticleUsing infineon models in Orcad
See section 6.2 For ORCAD and change the settings for the simulation options.
View ArticleAssembly extended register
Hello, I am using the Free Entry Toolchain and want to use some inline assembly. Code: static void maddq(int64_t *out, uint32_t a, uint32_t b){ __asm__ ("madd.q %0,%0,%1,%2" : "+d" (*out) : "d"...
View ArticleClik here to view.
TLE5012B. CRC calculation trouble.
Hello! I am using TLE5012B via SSC interface (bit bang mode, not hardware spi, connection according to the datasheet). I write to sensor command 0x8012 (read angle value) and then i get two words...
View Article