Clik here to view.
[SPI DMA] Missing first byte
Dear Infineon, I'm currently working on a XMC4700-F100F2048 configured in DAVE with an SPI_MASTER app and a DIGITAL_IO to manage the SPI_CS. SPI_MASTER app is configured in DMA mode both in transmit...
View ArticleXMC1300 GNU GCC Linker HELP
Been stuggling with the for 2 days not. Trying to use the GNU GCC compiler with the XMCLibs sdk. I am using the GCC startup_XMC1300.S along with the XMC1300x0032.ld using the following gcc command...
View ArticleQuestions about the bandgap-reference-circuit specified in the datasheet
Hi, I am reviewing the datasheet to use the TLE9867QXW. I have a question about the bandgap-reference-circuit during the ADC review. 1 Can I measure bandgap-reference using a bandgap-reference-circuit...
View ArticleI am looking to use the IRMCK099 in a new design, but I have the following...
The data sheet answers your question: IRMCK099 contains the flexible Tiny Motion Control Engine (TinyMCE) for sensorless control of permanent magnet motors (which is PMSM) over the full speed range....
View ArticleAurix tc267d
hi, I'm new to AURIX. I've tried implementing an SPI communication using AURIX as my master. I'm facing issues that my tasks are not getting called in mentioned time. There are various tasks in my...
View ArticleConfiguration of DMA for Transfer vom RAM to EBU Interface on XMC4700
Good Morning Everyone, currently I try to config the DMA Channel for transfer 240x320 unit16_t values from a Frame buffer in my RAM to the EBU Interface. But with the current configuration and...
View ArticleSDMMC app upgrade issues (4.0.22 -> 4.3.22
Thanks for that Jesus, I have removed the LED signal and it works perfectly. I might need to reinable it at some point in the future but by then a new version of the app will be released. I couldn't...
View ArticleAURIX 26X interrupt and timer confuration
Hi, I am using Infineon aurix 267D for SPI communication with TDA. I am able to transmit and receive data properly. In run mode I want Aurix to send command after each 100 ms interval but it is taking...
View ArticleAURIX TC22xL oscillator
Hi We are unable to find informations about internal oscillator (RC or whatever) in SAL-TC222L-16F133N in datasheet, is there such thing implemented in that device? If it is, how oscillator source is...
View ArticleSDMMC app upgrade issues (4.0.22 -> 4.3.22
Thanks for that Jesus, I have removed the LED signal and it works perfectly. I might need to reinable it at some point in the future but by then a new version of the app will be released. I couldn't...
View ArticleTLF35584 INIT to NORMAL MODE
I need to verify this still but I have a similar problem and I think it is down to the differences between different versions of the chip, make sure you have the one you think you have.
View ArticleSSC Tool, SSC_Device, and structure for category strings
The SSC project settings are cached in the SSC app and it's probably picking up "XMC_ESC" from the default Infineon configuration. You can delete this from SSC > Tool > Options >...
View ArticleTricore TC1782 GPT Pins
Hello there. I have been trying to read TC1782 on-board and trying to figure out which pins could be GPT S1 and GPT S2 on MCU? Any help from you guys will be highly appreciated. Its Infineon Tricore...
View ArticleTC26X Trap4 issue
hello, when I debug the S/W,the programming will go into trap4 issue,tin number is 2; it shows the data access synchronous error trap occured. do you have encountered the similar issue and what's the...
View ArticleOn how to use matlab/simulink to simulate EVAL_M1_099M.mdl
There is some guidance available in application notes for MCE IRMCx100 series: 3.3 Simulink MCE Design Components or in this document Reference Manual in section 5
View ArticleSeveral questions about using iMOTION
First: The IRMCK099 combines the iMOTION motor control engine (MCE) with all peripherals required to realize a complete variable speed drive (for permanent magnet motors). The steps to develop a motor...
View ArticleBeginner question: first Board with XMC1100 not recognized by debugger
Hello all, my Name is Michael. I am just in the progress of replacing some hard-to-come-by Atmel AVR´s with something more modern. ATM i am having a closer look at the XMC1100 famity, and bought the...
View ArticleClik here to view.
Distance2Go Evaluate recorded data from RadarGUI
Hello, I'm trying to evaluate data I recorded with the RadarGUI to get the same results as the RadarGUI shows me. I'm working with a Distance2Go Demo Board. The D2G board detects two targets and...
View ArticleUpgrading GCC in DAVE4
WARNING FOR ALL DAVE USERS: The GCC version 4.9.3 supplied with DAVE 4.4.2 suffers from optimizer bug that can drop null-pointer checks from your code. I just found in my own code that the bug...
View ArticleExternal Line IRQ
I use .edge_detection = XMC_ERU_ETL_EDGE_DETECTION_BOTH. for exertnal IRQ This trigger my IRQ function void ERU0_0_IRQHandler(void) { if "falling edge" { } else { } } Now i have to find out the...
View Article