Where to map a trap vector table used by a Tricore?
Hi again, do you know where to map a trap vector table used by a Tricore ? Thanks! Bernie #8042000 13136
View ArticleHow can i debug my code when i encountered Trap?
Hi, How can I debug my code when I encountered Trap? Thank you and regards Bernie #8042000 13007
View Articlepulse output at TGO when TRIG register is written
Hi, We need to read contents of some RAM memory locations of TC39x-ED micro. Can we configure OCDS such that whenever a write to TRIGS register happens, a pulse is produced at one of the TGO pins?...
View ArticleHow to get the max speed of motor
Hi, I use the FOC demo code to drive my motor .My motor's nominal speed is 30000rpm.In my applicaiton, I got the max speed is 23900rpm though I added the speed command ,it held 23900rpm. Does the...
View ArticleClik here to view.
TLE9879 Evaluation Kit using BEMF
Hi Fiz, thanks a lot for helping me! Here are the configuration files. Attachment 4295 I hope you find my problem! Best regards Eto ????? TLE9879QXA40.zip‎ (477.2 KB)
View ArticleXMC 4700 SPI with XMC Libs
Hello, I am fairly new to the XMC world. Has anyone an working SPI example for the XMC 4700 that only uses XMC libs? (No Dave apps allowed in my project) I tried to use the provided XMC 4500 SPI...
View ArticleCant establish connection to target AppKit_TC297B
Hi How did you make the connection to the target board? via micro-USB cable? Did you select the correct target for connection? (ie, Application Kit TC297B? If you go to Windows -> DAS -> DAS...
View ArticleXMC4800 write to flash
Your software part which writes some data into the flash (or erase sectors) should be located in the RAM. All interrupts should be disabled during flash erase and write operations. Check this in your...
View ArticleCan a trap be generated within the trap handler?
Hello all, I wonder if a trap can be generated inside a running trap handler? Thank you! Best regards Lucas #8042000 13004
View ArticleIs it possible to use 5V ADC reference in Aurix?
Hi AURIX Community, can I use 3.3V or 5V as a reference voltage for VADC in AURIX TC2xx? Thanks and Regards Lucas #8042000 12992
View ArticleUsing NC or NC1 balls for PCB routing?
Hi all, can the NC (No Connect) or NC1 marked balls be used for customer PCB routing? Thanks and regards Lucas #8042000 12982
View ArticleWhere to buy AURIX TriBoard Extension-Board?
Hi all, I would need more TriBoard Extention boards. Could you help and tell me where can I buy it? Thanks! Lucas #8042000 12947
View ArticleDocuments for schematics and PCB design guide
Hi all, I am looking for documents providing schematics and PCB design guide. Can you help, please? Thank you and best regards Christine #8042000 19741
View ArticleIs CPU watchdog and Safety watchdog the same for Aurix TC23x MCU?
Hi AURIX Community, Is CPU watchdog and Safety watchdog the same for TC23x MCU? Thank you and best regards Christine #8042000 19643
View ArticleWhy do unexpected bus errors occur when code is doing nothing?
Hi all, I wonder why do unexpected bus errors occur when the code is doing nothing? Thanks for your help and best regards Christine #8042000 19678
View ArticleHow is the CRC calculated with the DMA?
Hi AURIX Community, how is the CRC calculated with the DMA, for data and addresses? Thanks! Best regards Christine #8042000 19724
View ArticleHow many interrupt priorities can be set in Aurix?
Hi, How many interrupt priorities can be set in Aurix? Thanks & Regards Bernie #8042000 19611
View ArticleHow do I access another core's memory?
Hi Aurix Community, could you please help with the following: how do I access another core's memory? Thank you! Best regards Bernie #8042000 19638
View Article