What is the difference between write-page once "WOP" Protection and one-time...
Hi Bernie , Both WOP and OTP are protect configurations which can be applied for the Pflash. Both could be configured for each logical sector of the Pflash through UCB_OTP. If OTP protection is...
View ArticleHow to manage interrupts with same priority with a Tricore CPU ?
Hi Lucas , With AURIX™, there cannot be several different interrupts with same priority managed by a same Tricore CPU. So each interrupt will have its own priority level. To manage several interrupts...
View ArticleClik here to view.
[Ethernet] iLLD driver issue on TC29x
Quote: Originally Posted by vitorroriz I debugged the code once again with the help of my Master Thesis Mentor here in Toyota Motorsport. The problem was that the DMA was receiving the local addresses...
View ArticleHow to use POSIF in DAVE4.4.2?
Just found an issue - In the DAVE app configuration, the max value for "Ticks per revolution" is listed as 65535 however this is multiplied by 4 in the encoder_posif_conf.c file for...
View ArticleDiscontinued IRDAKO705169
Max quiescent IQCC (VCC supply current) is 3.35 mA. IQCC increases during PWM operation by about 20%. It is best to design the power supply to provide at least 5x the operating IQCC. In this case...
View ArticleTricore-TC277 STM(System timer)
Hello Cwunder, Thank you very much for the link. Please can you explain me the scope of the function IfxStm_increaseCompare(g_Stm.stmSfr, g_Stm.stmConfig.comparator, TimeConst_100ms);...
View ArticleGPIO XMC 2Go Board
Hi. I am programming an Infineon 2 Go and I use DAVE. When I want to assign GPIO P0.14 and P0.15 in Package View they appear as non-feasible when they are available on the board. P0.12 and P0.13 appear...
View ArticleWorking with XMC, Hello World and ADC Basic
Hello, I am fairly new to the XMC family but I not new to C language. Could someone please share resources for getting familiar in DAVE? I intend to write a code for Hello World where I just need the...
View ArticleIssue while programming IRMCK099 OTP
Hello all, We started using the IRMCK099 about 3 years ago, and we always were able to program the OTP correctly, both Fw and parameters. Now we had to come back on the project to modify the .bin and...
View Article[SOLVED] tle987x debugging problem with segger j-link
Hi Murat, great to hear! If you experience more problems you can always ask the forum our contact our technical assistance center: https://www.infineon.com/cms/de/abou...-support-form/ Best, Fiz
View ArticleClik here to view.
UCB_DFLASH_ORIG and UCB_DFLASH_COPY reprogram
Quote: Originally Posted by MoD Handling of UCB must be always very carefully, e.g. don't make changes in ORIG and COPY at the same time. As far as I know, the default behavior of iLLD drivers + base...
View ArticleClik here to view.
Cant establish connection to target AppKit_TC297B
Hi, I have an Application Kit TC2X7. I have installed the hitec IDE and tried to flash an existing example program to the board. The build of the program is finished. But its unable to connect to the...
View ArticleFlashing TC297_TFT_Application_Kit Problem
Hi, Have you found a solution to this problem? I seem to get the same error but already while flashing a sample program to the board. Thanks in advance Best Padma
View ArticleIs dedicated interrupt resource assigned for each pin with external pin...
Hi all, is dedicated interrupt resource assigned for each pin with external pin interrupt ? Thank you for helping! Best regards Christine #8042000 13448
View ArticleHow many SENT channel can support SPC (Short PWM Code) protocol?
Hi AURIX Community, do you know how many SENT channels can support SPC (Short PWM Code) protocol? Thank you! Best regards Christine #8042000 13459
View ArticleHow can I measure the average IPC for my application code?
Hi all, How can I measure IPC (Instruction Per Cycle rate) or other useful parameter for my code? Thank you and best regards, Christine #8042000 13272
View ArticleHow to use DSADC, TIM and MCS to do peak&hold control for GDI system?
Hi, I wonder how to use DSADC, TIM and MCS to do peak&hold control for GDI system and which aspects should pay attention to? Thanks and regards, Lina #8042000 13236
View ArticleDifference in variable allocation: LMU vs CPU core memory
Hi, in terms of memory access time in AURIX, what is the difference if variable is allocated at LMU (Local Memory Unit) vs CPU cores memory? Thanks and regards Lina #8042000 13198
View ArticleCan I use the miniWiggler and MemTool to program the UCB blocks?
Hi all, I wonder if I can use the miniWiggler and MemTool to program the UCB blocks? Thanks for your help and regards Lina #8042000 13156
View ArticleCan I use the lockstep core to run different code?
Hello Aurix Community, If I don't need the lockstep, can I use it to run different code? Thanks! Bernie #8042000 13140
View Article