Clik here to view.
XMC 4300 Ethercat Dave Manual Pin Allocator
Hi, I am just starting with the XMC 4300 Ethercat Dave example from here https://www.infineon.com/dgdl/Infine...554f4951cc6447. My problem is on Page 28. When I open the Manual Pin Allocator my output...
View ArticleAurix Triboard TC277Tricore clock
Hi UC_wrangler, yes, indeed i found this macro already and it is defined to 200Mhz, But when I managed to retrieve the cpu frequency IfxScuCcu_getCpuFrequency(IfxCpu_getCoreIndex());(stm example from...
View Articlelsl section
Hi Lukas, Since pspr_function was prototyped with the inline attribute, it will most likely have been inlined into the body of the function that calls it. Hence there is a good chance that your...
View ArticleTC3xx has SOTA feature How it works
How SOTA feature is operated and swapping of PFLASH Banks takes place
View ArticleClik here to view.
Tricore-TC277 STM(System timer)
Hello All , Can any one please explain me how the STM(system timer logic works). i can understand it is a 64 bit timer and the value cannot be read in full so it is spitted into two registers. The...
View ArticleCAN not working after running bootloader
Thanks for the reply. You are correct, it ended up being a problem with the overall clock system. Our bootloader had to clean up the clock configuration registers before jumping to the application. It...
View ArticleTricore TC277 - SPI driver in FreeRTOS
Hello Everyone, I am working on FreeRTOS using TC277 micro-controller. i am trying to develop Infineon QSPI driver into FreeRTOS. Has anyone got any suggestions or any examples to implement. I have had...
View ArticlePWM routing to PORT & ADC simultaneously?
Hello, If I use a single ATOM channel for PWM generation in TC387 microcontroller, can i use it for ADC triggering & external sensor supply as well. Can this single PWM serve these 2 purposes(Port...
View ArticleSMU Configuration with FSP Signal Port 33.8
Hello, I have a problem with configuration of Port 33.8 to be the FSP output signal of SMU. I have followed the Aurix user manual and SafeTlib manual and i'm doing the following: The Port 33.8 is...
View ArticleClik here to view.
commutation table of BEMF demo code
Hi Fiz, Thank you! I find the picture as below about my motor's commutation sequnece.Can you give me an example about how to write the code according to this picture. Attachment 4273 Best! ?????...
View ArticleUsing Infineon TLE493D-A2B6 with Teensy 3.2 (or arduino)
I am using (or attempting to use) a teensy 3.2 using the Arduino IDE to interact with a 3-axis hall effects sensor (the Infineon TLE493D-A2B6). The sensor can only be interacted with via I2C, and it...
View ArticleDiscontinued IRDAKO705169
Hello, I'm trying to repair a motor driver for an ASKO W6863. I've replaced the blown LNK304GN which supplies +15.4V to (what I assume is) the low side control supply of the IRDAKO705169, but the...
View ArticleDevelopment tool for SAF-XC161cj-16F40F bb
I´m needing a step by step to program a saf c164ci lm for my client project, what software, what adapter to program this device. I´ve tried this dave but I didnt find the device in the library. Thanks
View Articlehelp with med17.5.2 post is gone now
i ow got ktag, and i can't seem to get the ecu to boot
View Articlecurrent sourceï¼15A
I want to make a 15A constant current source. I hope you can recommend the relevant circuit.Specific requirements are as follows: 1. sinking current to ground, Lithium battery discharge (29V) ,15A...
View Articletle987x debugging problem with segger j-link
Hi Fiz, I connected VS pin for flashing. I have some doubts about my j link segger. Can i use tle987x evalboard to swd debug another mcu which is on tle987x evalboard? I mean debuging one tle987x...
View ArticleAdd C++ class function in main C source file
Dear reader! Embedding C++ in C isn't directly possible, vice versa does. But it is really possible if you use a cpp wrapper where you return cpp functions to c. Useful link:...
View ArticleClik here to view.
Promoted Link List
Attachment 4282Attachment 4283Attachment 4284Attachment 4285Attachment 4286 ????? Banner_iMOTION_323x323.jpg (20.0 KB) IMM100_Button_323x323.jpg (24.6 KB) IMC-100-Series-232x232_en.jpg (59.9 KB)...
View Articleevrsb during standby mode is larger than the spec. What could be the reason?
Hi Christine , First please check whether the temperature is around Tj=25°C, as this the condition for the datasheet spec. Otherwise, this might be due to the fact that the device failed to enter the...
View ArticleHow does the memory protection work?
Hi Lucas, There are three different protection mechanisms: Access enable protection Bus Memory Protection Unit (MPU) CPU MPU Access enable protection filters peripheral accesses using master tag IDs...
View Article