Clik here to view.
XMC4500 flash readout protection
Hi ahndy, You can follow the steps in the power point slides. The password and procedures are quite sensitive, hence please take special care on these. If possible have a socket for your MCU, in the...
View ArticleHow to use DAVE to combine PWM_BC with POSIF in APP project
HI, PWM_BC APP generates pulse width modulated output for block commutation (trapezoidal) to drive three phase two level voltage inverter. The APP uses CCU8 peripheral for generating PWM and it also...
View Article256 KB of contiguous memory in XMC4700?
For those following along at home, the diagram in the previous post is for a different part. If you have updated DAVE to the Feb 15 version you should have no problems. USB_RAM normally starts at...
View ArticleClik here to view.
XMC1000/4000 Tip of the day: External pin interrupt function with USIC channel
If a USIC channel is not used for serial communications, its DX2 input pin can be used for an external pin interrupt function. A rising, falling or either edge on the selected DX2 pin can be configured...
View ArticleError in Hardware request
I also tried to debug and I get a further error: " Error while launching command: C:\Davev4\Dave-4.1.4\eclipse\ARM-GCC-49/bin/arm-none-eabi-gdb --version".
View ArticleXMC4100 System File Errors
I am creating a new XMC4108 project with Dave v4. The project generates code and builds fine on Dave. When i import the project to Keil it is unable to build due to the following line in the...
View ArticleTricore 1767 Execution Time Measurement
Hey, I know this is old but I think many people will have similar problems. I finally solved it like this: Code: void benchmark_start() {...
View ArticleClik here to view.
Power Management Selection Guide 2016 available
Power Management Selection Guide 2016 Mobile devices, cellular infrastructure, motor control, lighting, computers or networking equipment todays advanced systems must be developed in ever-shorter...
View ArticleXMC4400 HRPWM Phase Shift
Hello, I'm using two instances of the HRPWM-App and want to use them to control a Full Bridge with Phase Shift as shown on pages 16 to 18 in the training file...
View ArticleAutomated Code Generation and Build of a DAVE project
Has there been any update on the ability for command line build?
View ArticleReading out TLI4970 current sensor with XMC4500
Hello, I am building a current sensing appliance. I am using XMC4500 application processor and TLI4970 current sensor. How should I set up the SPI Master App on XMC4500? I've already played around with...
View ArticleSettings for DC-syncronous (or SM+SYNC0) mode
Hello everyone, I tried to get DC clock synchronization working on the XMC4800 EtherCAT kit -- both with the current "XMC4800 Relax EtherCat Slave SSC"...
View ArticleClik here to view.
XMC4400 - Cannot read register after de-asserting reset from VADC
I'm using a Hexagonal XMC4400 board (XMC4400 F100K512) and I cannot read the register BFLNP from the ADC groups when I de-assert the peripheral reset. I also noted that in the debugger the register...
View ArticleClik here to view.
Brand New Version does not work
I have the same problem. Additionally I created a new Workspace and started a new project. In this case DAVE gets stuck on adding Apps. I attached the log file of it trying to add a DIGITAL_IO app. The...
View ArticleGPIO tri-state on reset unclear - help please
Which GPIO pins are you using and what configuration setting did you do on the IOs?
View ArticleClik here to view.
Dave 3 run problem
Dear Members, I tried many times to generate the codes according to BLDC example in Dave 3 and faced problems as attached file. The warnings are "Resource mapping failed, please review the user defined...
View ArticleXMC_SCU_HIB_SetRtcClockSource function access to NULL pointer
hi, i have a project with a xmc4400 which don't use a hibernate section and rtx_xtall. At start-up the system stay infinite loop inside at function XMC_SCU_HIB_SetRtcClockSource. The register...
View ArticleSoftware CORDIC
Hi, Im working on an autocalibration algorithm for analog GMR angle sensor products. I wanted to implement a (software-) cordic to calculate the angle out of the raw cos and sin values. For...
View ArticleDave Apps C++
You may look here: http://www.infineonforums.com/thread...nd-c-with-DAVE I guess you need to do a clean all to make it work. See the above thread for more pitfalls. I hope Infineon is fixing stuff.
View Articleproblem with GLOBRES register (XMC1100)
Hi Travis! Thanks for the help. I came to realize that I had a mistake. I read this in the datasheet: "When the result register is read via the application view (GLOBRES), the corresponding valid flag...
View Article