Clik here to view.
Econo modules with internal shunts
Hi SiCguru, Modules with integrated shunts offer a space saving alternative of high accurate current measurement with good heat dissipation. You don't need to think about the heating of the PCB by the...
View Articleutilization of IGBT7 in Econo?
Hi Wen, Yes. Due to increased gate charge the possibility of parasitic turn on is lower than for IGBT4. This makes it suitable for unipolar gate supplies. The other benefit of higher Qg is better...
View ArticleLBIST Run Completion Reset and RAMIN field of HF_PROCONRAM for Aurix 2G
Hello Support, At the end of successful run of LBIST, there is a reset automatically triggered by the TC3xx parts [Aurix 2G]. Under that Reset due to LBIST, if the contents of HF_PROCONRAM.RAMIN=2'b10...
View ArticlePressFIT compared to solder Pins?
Hi TondGy, PressFIT pins use the cold welding contact principle. They are robust against vibration, have a good electrical conductivity and are thermally robust. For the module they offer a failure...
View ArticleAurix 2G LBIST Warm Reset and RSTCON2 USRINFO Reset
Hello Support, Is there any register within Aurix 2G whose values are maintained same across LBIST Reset occurrence? Best Regards
View Articlecan't download aurix-studio
ive tried to download AURIX Development Studio software via the link given from aurix official website. but it kept to stop downloading from 75mb(total362mb) i can not link the download links here,,...
View ArticleSPI APP bug on XMC4800
Hi,saili_desai; Do you called the SPI_MASTER_Receive() in your interrupt routine? Thanks & regards.
View ArticleEmulator Debug Port Secure error on Trace
Hi there are total 4 sets of BMHDx_ORIG & BMHDx_COPY, if BMHD0_ORIG is wrong, it will look at BMHD0_COPY, and the sequence follows to BMHD1/2/3. you mentioned u erased BMHD1/2/3, this will prevent...
View ArticleIRMCF171 I can not start
Technical support answered me and sent a link http://www.mips.com/products/softwaretools/legacy/8051/. Such a link does not exist, the site redirects to the main page https://www.mips.com/ Maybe...
View ArticleClik here to view.
IR2136 application circuit
Quote: Originally Posted by Srivatsa Pls check if the MOSFET Q8 is turning ON. Also, check the status of Fault pin. You can write to me at srivatsa.raghunath@infineon.com and I will see if I can get a...
View ArticleClik here to view.
XMC4200 : bit frame generation
Hello!!! I'm using Infineon XMC4200 to generate in a certain output port , for example Port2 , 8 contemporary bit frames that have to be repeated cyclically for example every 1 sec. Every bit frame is...
View ArticleXMC4500. USB-device. Zero-length packets in isochronous IN-endpoint - how to...
I need a fast real-time data stream from device (USB-device) to PC (USB-host). I use a large isochronous endpoint (packet length <= 1023 bytes). The data is transmitted, but very often in frame...
View ArticleEtherCat XMC4300 - pin allocator is not working
Hello, I´m not able to select Pins in the XMC 4300 EtherCat example: If i try to select Pin Number (Port) it ends in - Solver time out hast occured..... I can generate ,compile and also run the example...
View ArticleADC_MEASUREMENT_ADV 4.0.14 with SCAN_APP creates wrong config
When using ADC_MEASUREMENT_ADV with ADC_SCAN_APP setting, the created mask for loading GxASSEL is wrong e.g. new project for XMC4400x64 add ADC_MEASUREMENT_ADV: Number of Channels 3 config Pin...
View ArticleFF1800R17IP5 with Uge=0V/+15V
Hi, Is, possible to use the FF1800R17IP5 power module with unipolar gate voltage (Uge=0V/+15V)? Ty Max
View ArticleBLDC_SHIELD_TLE9879 questions.
As I understand the board has a firmware ready to operate from SPI master (the board serves as SPI slave). But I haven't found any documentation regarding the communication protocol and commands. I...
View ArticleBLDC_SHIELD_TLE9879 driving DC motor.
The question is - how can I drive a DC motor with the board in H-Bridge topology?
View ArticleJunction temperature measurement
Hi guys, Im using an IKW40N120H3 in a boost converter. What is the best way to measure the junction temperature of a device? Thanks!
View ArticleHow to press in the EconoPACK 4 in the PCB?
Could someone here explain, how to press in the EconoPACK 4 in the PCB?
View ArticleAurix 2G LBIST Warm Reset and RSTCON2 USRINFO Reset
The Standby Controller XRAM (0xF0240000-0xF0241FFF) is not affected by LBIST.
View Article
