SENT (SAE J2716) receiver source code for XC2000
Good morning We would need to implement SENT protocole onto an MCU like XC2287 lacking a dedicated SENT peripheral to process data issued by a Magnetic Angular Position Sensor (AS5270). We found the AN...
View ArticledV/dt induced turn-on
Hi Infineon, several times I read about dV/dt induced turn-on? Can you please explain what it means? Thanks and BR Melanie
View Article62mm SiC MOSFET gate driver design
Hi Walter, You can find gate driver guideline for CoolSiCâ„¢ MOSFET based modules in AN2018-09 BR
View ArticleEasy3B
Hi Melli, This is a new package in our Easy Power Modules family. The Easy3B has the size of two Easy2B integrated in one single package and has the same height as other Easy packages (12mm). The...
View ArticleRg for drives
Hi Max, For drive applications it is important that du/dt is in the range of 2kV/us-8kV/us (depending on the rated motor voltage), higher values can endanger coil insulation and bearings. Typically for...
View ArticlePCB for Econodual with pressfit
Hi Nick, For the PCB we recommend first to take a look in the datasheet of the corresponding module. There you can find the all needed dimensions. Regarding the other relevant topics please have a look...
View ArticleCan LBIST fail based on Temperature assuming Voltage levels are all within Spec?
Hello Support, In the Aurix 2G Safety Manual, there is a section "ESM[SW]:MCU:LBIST_RESULT" where the following is mentioned: "Therefore it might happen that under extreme operation conditions a single...
View ArticleBenefits of the IGBT7 technology
Hi SiCguru, The benefits are the lower on state voltage for the IGBT and also for the freewheeling diode, the overload capability at 175°C during motor overload condition, the enhanced controllability...
View ArticleClik here to view.
Difference IGBT / MOSFET
Attachment 4525Hi Melli, there are few analogies between MOSFET and IGBT and a main significant difference. Regarding the analogies: - Both IGBT and MOSFET are voltage controlled devices - Both IGBT...
View ArticleClik here to view.
Problem running TLE9879 EvalKit sample program (BLDC_BEMF)
Hello, I have just received the TLE9879 EvalKit v1.3, and I am having a problem running the BLDC_BEMF sample program. I have followed all the instruction for installing the toolchain to develop using...
View ArticleClik here to view.
Number of Bytes received over UART when using DMA
Quote: Originally Posted by rperry I was wondering if there is a way to check the amount of Bytes received from the UART bus (im thinking by checking the status of the DMA)? See of field BLOCK_TS in...
View ArticleTLE5012B rotation direction change angle error 1 degree?
My customer use our product to test rotation repeat performance. He rotate the motor CW and then CCW, it can't return to original point. How to fix this issue?
View ArticleClik here to view.
Using Aurix TC27x MCAL drivers supported for DB step on a DC step
Hi You need to check the MCAL package Release notes -> chapter 3 Tool Information. It will indicate which steps & derivative the package has been qualified on. Please see attached for example....
View ArticlePQR Files
Hi AnniLe ! Our PQR's (product qualification report) describes the characteristics of the product with respect to quality and reliability. You may know this document under its former name QPAC (product...
View ArticleRAM initialization after standby mode
Hi, Currently I'm using standby mode in my application, I have several configurable variables I set during run time. my init for those variables looks like this: Code: trigger.c trigger my_trigger ={...
View Article62mm modules and thermal paste
Hi SiCguru, I think you mean the process of applying thermal paste manually. In the AN 2012-05 (chapter 8) you can find the recommendations on how to do this. BR
View ArticleThermal paste for 62 mm, too?
Hi TondGy, Yes, we have 62 mm modules with pre-applied Thermal Interface Material (TIM). More information about this material and available modules with it you can find here. BR
View ArticleIGBT in general
Hi all, I would like to add another question that fits into this context. How has the IGBT technology evolved? Thanks!
View ArticleEcono modules with thermal interface material ?
Hi Max, All modules available with TIM you can find here. BR
View ArticleInserting angle from Arduino into TLE9879
Hi, We're evaluating the BLDC_SHIELD_TLE9879 with an Arduino Uno. The Arduino uses SPI to communicate with the TLE9879. We have not bought a programmer/debugger yet. The shield is running stock...
View Article