Unable to do send data in UART comminication
I am using XMC 2GO kit. I tried to do UART communication with DAVE software and a serial communication software Docklight. I successfully sent strings to Docklight but whwn I tried to send data back...
View ArticleXMC4800 USB BULK Mode driver
Dear All, I am working on USB Device driver development. I need transmit some data from the device to USB host. I got following example "USBD_VCOM_APP_Example_XMC45". However it is an APP based...
View ArticleQuestion about SRAM declaration at XMC4700
Short question I work with a XMC4700 board Overall, the controller has 352 Kbytes SRAM from data sheet: PSRAM 1FFE 8000-1FFF FFFF hex 96 KByte DSRAM 2000 0000-2001 FFFF hex 128 KByte CSRAM 2002...
View ArticleUsing a driver (IRS21844S) without the boot cap circuit
Hi, I'm trying to figure out how to use an H-Bridge driver chip without resorting to the boot strap cap method. The FETs themselves are switching a +96V circuit, and what I'd like to do is connect a...
View ArticleM1-CM610N3 Power Board -- EXAMPLE FILES
Hallo, I have just bought the new EVAL-M1-CM610N3 power board equipped with the CIPOS mini IKCM10L60GA, to be tested with the Eval M1-1302, the control board with XMC1302. I have tried to find some...
View ArticleClik here to view.
Infineon TLE9879 Eval Kit Bridge short problem
Thanks God. Someone is there who answers in the forum. I has lost all hope from this Forum. Thanks M.K. for answering. After so many days I checked the forum and I am answering right now. I have...
View ArticleXMC4800 Automation Board V2 - How to debug / program ?
HI Marc, to quote User Manual: "The XMC4800 Automation Board-V2 supports debugging via a 10-pin Cortex™ Debug Connector. To program and debug the chip any standard ARM™ debugger can be used." Example...
View ArticleUsing a driver (IRS21844S) without the boot cap circuit
Hi, I'm trying to figure out how to use an H-Bridge driver chip without resorting to the boot strap cap method. The FETs themselves are switching a +96V circuit, and what I'd like to do is connect a...
View ArticleMicrocontroller TLE9879QXA40
Dear M.K, I have 2 TLE9879 Eval Kit but both of the board shoe Bridge Drive Short problem. It has been almost one and half month but still Infineon TAC are not able to resolve this issue. I really...
View ArticleHelp develop a Joystick with XMC4500 with TLE493D-A1B6 3D Magnetic Sensor,...
Hi everyone, I'm trying to do an Open source project with the XMC4500 and the 3D magnetic sensor TLE493D. The idea is to make a Standard Joystick with two control levers with the TLE493D, 13 Buttons, 2...
View ArticleClik here to view.
FAQ for XMC4800 EtherCAT
Quote: Originally Posted by marzoel ...Does really no one has the PHY selection issue? Which PHYs do you use with the XMC4800? Thanks in advance, Martin I had the same problem with Broadcom. I...
View ArticleUsing a driver (IRS21844S) without the boot cap circuit
Hi, I'm trying to figure out how to use an H-Bridge driver chip without resorting to the boot strap cap method. The FETs themselves are switching a +96V circuit, and what I'd like to do is connect a...
View ArticleUsing a driver (IRS21844S) without the boot cap circuit
Hi, I'm trying to figure out how to use an H-Bridge driver chip without resorting to the boot strap cap method. The FETs themselves are switching a +96V circuit, and what I'd like to do is connect a...
View ArticleDebug Issue
Hello, I am newbee on Dave4. I am trying to debug my code and getting this error: No source available for "main() at 0x100026ae" But some how Code is working it does intended function. Only thing is i...
View ArticleProblems downloading Dave4
I'm trying to download Dave4 from the "personal download link" I was emailed, but it's impossibly slow, on two different networks. The download starts at an estimated 4-5 hours, and often gets as far...
View ArticleUCB_DFlash read and write protection
where is the support ????? this topic opened from Nov 6th 2017 and till now there isnt any reply why ?
View ArticleClik here to view.
TLE9879 Eval Kit Bridge drive Not Functioning
Dear all, In tle987 Eval Kit, I generate PWM using CCU6 and check the output in the Pins P0.x & P1.x and it functions Ok. But when allow the PWM to connect with Bridge Drive(BRDV), I do not see any...
View ArticleConfiguration settings in IFX configwizard
Hi, Can you please further explain what you want to do? How to activate the Bridgedriver, is already explained in this thread: https://www.infineonforums.com/threa...ot-Functioning The Input voltages...
View ArticleTLE9879x - NAC and NAD
Hello, The NAD and NAC values are explained in the "Bootrom User Manual" and in the "FAQ Application Note". Here are the direct links to the product pages, where the documents can be found:...
View Article