Clik here to view.
Problem programming new TC1796 with MemTool
Hi All , I’m using MemTool and trying to program a new TC1796 micro and have met the following error If I change the step in MemTool the padlocks go away but the part fails to program Has anyone some...
View ArticleXMC1400 Problems changing BMI from UART to SWD
Hi Deni, do you have solution for me. I have already done update of J-Link. But its show still the same message: Firmware is too old. Regards Michael
View Article12V/15V power supply rating for gate driver 1EDI60N12AF
Hi, I'm looking for a suitable power supply for the gate driver 1EDI60N12AF. As it is a isolated driver, it uses two isolated voltages, 5V and 12V or 15V. My question is basically about the ratings of...
View ArticleAdd additonal area to the copytable of tc222
Ok, here is the problem. I have a bunch of variables that I need to have a ROM version of at a specific address and a RAM version at any RAM address. No problem yet, I just did two copies of each...
View ArticleClik here to view.
IR2136 Hardware Over current ï¼Why Output waveform thisï¼
Schematic diagram, Attachment 3522 ????? 360æªå¾18141223346268.jpg (76.6 KB)
View ArticleTle5012b e1000
Hi.. Looking at your code,seems as if you are not clearing the interrupt after every read i.e.Clear the interrupt after receiving each frame.
View ArticleProblems with EBU on XMC4700
Hi All, I am having trouble interfacing XMC4700 (100 pins)with NAND flash via EBU. In my project EBU lines are shared with NAND flash and FPGA. FPGA is configured to pull up all AD/CLE/ALE lines. So on...
View ArticleClik here to view.
IR2136 Hardware Over current ï¼Why Output waveform thisï¼
Schematic diagram, Attachment 3522 ????? 360æªå¾18141223346268.jpg (76.6 KB)
View ArticleClik here to view.
Can not flash new XMC1302 on custom board
Hello, I am not able to flash my XMC1302 on my custom board, I'm getting "Could not connect to target. Please check power, connection and settings.". It works perfectly fine with the XMC1300 boot kit....
View ArticleClik here to view.
IRF1404 in the market with defect
Recently, I bought a lot of mosfet IRF1404 from a seller who said to have imported from US such mosfets. When I performed bench tests on them, I realized they were original, but they had some...
View ArticleTC223 Starter Kit UART over DAP
HI All, I trying to find out if it's possible to have UART over DAP (external miniWiggler connected to board DAP port) in same way as it's achieved with on board miniWiggler. To be precise I want ot...
View ArticleXMC 4500 - how to enter Hibernate mode?
I'm currently working on the Hibernate mode. Have tried this code but this does not work for me and the description in the documents of Infineon help me unfortunately not further. Does anyone have a...
View ArticleMicrocontroler - Multiple I/O
Hi Jamesjgh, we have several products which can cover your functional request. Nevertheless further information are necessary, i.e. how does the input signal looks like and what do you want to switch...
View ArticleClik here to view.
Codesize arm gcc4.9 to arm gcc7 increased drastic
Thanks for testing. I extracted the section from the listing from my compilation. Attachment 3540 Attachment 3541 Can you please post your listing and if possible your compiler / linker log? In...
View ArticleEBU Addressing on XMC4700
Hi All, I am attempting to read memory via EBU interface. In my hardware ALE is connected to pin AD11 and CLE is connected to pin AD12. Based on addressing alignment mentioned in reference manual...
View ArticleUpgrading GCC in DAVE4
Hi. I think it should be mentioned that for a project specific toolchain the variable ARM_GCC_HOME has to be deleted in the global scope settings/properties. and adjusted in the project specific...
View ArticleDEMS-DK Kit not working
I recently bought a DEMS-DK kit. power supply and ethernet connections are OK but GUI is not responding. Is there any one successfully started this DMS-DK kit. very poor documentation
View Articletricore-gcc link openssl
Hey together, I need to link openssl for my project which will run on a AURIX TC275TP-64 later. I have problems getting the correct version of openssl for the tricore-gcc. Using the normal openssl libs...
View Article[Ethernet] iLLD driver issue on TC29x
I've found other bug that may help you. In my evaluation board, the pin defined for MDIO is not bidirectional. This has some implications in the iLLD PHY driver. For the non-bidirectional pin, the...
View ArticleSynchornization of Cores
Hi , Thank you for the detailed explanation. It helped a lot. Best regards Prakt
View Article