Distinguish Human from Object on Position2Go
Dear Sam__ Kindly share the information. we are working with P2G demo kit. and if this concept is useful then we may use in our project.
View ArticleClik here to view.
Connecting to IMC101T-T038 via IMOTION-LINK Debug Probe
Quote: Originally Posted by electronwrangler Hello, I am trying to connect to the IMC101T-T038 on my custom board using the IMOTION-LINK debug probe and am getting an error that says "MCEDesigner...
View ArticleWhat is an IPM?
Happy new year! :o What exactly is an IPM? What is the field of application? What products are available? Thanks :-)
View ArticleClik here to view.
DAP and Tricore PFLASH programming
Quote: Originally Posted by UC_wrangler The critical thing is to make sure your FSI and FSI2 clocks are as fast as possible. The code execution time isn't nearly as important. Also make sure your wait...
View ArticleWhich IPM is best suited for my application?
Dears, while checking out the Infineon website i was trying to find the best matching IPM for my configuration. Do you have a hint how or where to find the best suited device? Thanks in advance. Max...
View ArticleSmart MOSFET BTS50055-1TMA will it support 62A
Hi, I have been going through an application which requires 62A high side output with around 80A peak current support for 10s. Will this device suit my purpose. There seems two specification...
View ArticleLinux generated elf not working in Windows (sources not found)
This incompatibility between Linux and Windows is really annoying, especially when you have an already working setup for Linux that you want to try on an Evaluation Board that can be debugged only in...
View ArticleTc275 asclin uart
Maybe the example does not actually write anything to serial, just using some type of loopback? Which example are you using, there are more USART examples, I can try on my Evaluation Board to see what...
View Articlexmc1100
Hi, I am using keil uvision xmc1100 and the xmc peripheral library Could you please advise on which registers I need to set up so as to have PWM output on a specified pin.
View ArticleXMC1000 TIP of the day: Software TRAP for CCU8
Something I just discovered, a heads up for anyone driving a H-bridge with CCU: Based on the hardware manual of XMC4700/4800, the trap function appears to control the output pin control block directly,...
View Articleextract_raw_data.c "The device didn't send any message." after ~1hour of...
Got this from Infineon support: Quote: In the file “\Application\src\application.c” in the function body of “void app_init( void)” around line 144: One argument of the call to protocol_init(…) should...
View ArticleWake up after WFI
Hi Michael, I am trying to get the same behavior using XMC1100. I followed your instructions and I am able to generate an interrupt using a PIN event. I then put the device in deep sleep mode using...
View ArticleWhat is all pin status during standby mode on AURIX-TC2xx ?
PINA is 14.1 (ball A15 on a TC297). It's labeled EVRWUPA in the datasheet, which isn't a very direct link. PINB is 15.1 (ball A18 on a TC297). EVRWUPB in the datasheet.
View Articleevrsb during standby mode is larger than the spec. What could be the reason?
See PMSWCR0.PWRWKEN on page 595 of tc29xB_um_v1.3.pdf. The PMSWCR0 register details are on page 605.
View ArticleDisplay with xmc4800
Hi AjejeB I use this one with xmc4500 and xmc4700: https://eu.mouser.com/ProductDetail/...UGkTCMN%2FlCUI It works because uses SEPS525F as display controller i.e., the one defined by default in...
View ArticleWDT Counter behavior (not count down) on Application Kit TC27x / TC29x
Hello Support, For the following comments: " Some comments: 1) The Watchdog timers only count up (they do not count down) 2) The Watchdog timers are enabled by default after reset, however if you are...
View ArticleClik here to view.
Hall-Effect Detection
Dear Hall Sensor team We changed VS Voltage 12V to 5V as a attach file that is TLV4996K_VS. Attachment 4375 It has happened strange waveform as a attach file that low is 1.3V. Attachment 4376 So, We...
View ArticleSafety Watchdog write access by which CPU in Aurix TC3xx devices
Hello Support, In the Aurix TC3xx User Manual 1.4 version, "Separate ACCEN protection range for Safety Watchdog Timer" in Section 9.4.1.1 is mentioned. Can you please provide me the corresponding...
View ArticleMotor Speed Measuring
Hello wskeller, if you are using the block commutation example using BEMF you can use the function: uint32 Emo_GetSpeed(void) This will return you the actual motor speed. Best, Fiz
View Article