Using the RGB LED Lighting Shield to drive constant voltage LEDs
Hello, how can I convert either the Arduino Sketch or the Dave v3 (RGBLED_2_Safe) to Dave v4. BTW, there is no Dave v4 example under the RGB Shield documents...
View ArticleDAVE 4 Versions
Hi, I've got a related question. Is there a download link for older Dave 4 Versions? I've got a project made with the Initial version and importing it to Dave 4.2.4 fails. The apps are all there but...
View ArticleIn Application Programming and XMC4800
Hi, I am trying to explore infineon XMC4800 in my product development. I am new with infineon products. I am families with TI, microchip , NXP, ATMEL products. I want to use in application programming...
View ArticleIso1i813t
ISO1I813T EVAl board documents having following description. I have found description that ISO1I813T can be used in direct mode also. (See blue highlighted text) I have not found any documents how can...
View ArticleISO1I813T - PCB foot print , symbol and application note with code
hi, I was reading Infineon-ISOFACE_Reference Design-PB-v01_00-EN.pdf file on infineon website. It was mentioned Application Note , User guide , PCB description , PCB layout , to down-load from...
View ArticleXMC1100 40Pin QFN - SDW1 issue
great to see these forums are well serviced......Nearly a month on and no one from Infineon can be borthered to comment on this issue
View Articlevery weird issue debugging XMC4700 in DAVE4 - pls help
Hello, I seem to be unable to Debug my XMC4700 Controller on a custom PCB (no infineon kit) using DAVE4. However, running DAVE3 there is no issue and works as it should, using exactly the same setup....
View ArticleXMC1302 XMC1000_BmiInstallationReq(0xFFC0)
Hello AAH, Regarding the BMI switching sequence, did you power off and on the board (plug out from USB then plug in again) before step 4 to read back the new BMI value? As long as this is done, you...
View ArticleFreeRTOS: Wich Version for XMC4800 Ethercat Relax Kit
Dear all, I wan't to extend the given Ethercat solution running based on FreeRTOS. Which Version is running well with this kit ? Can I simple use the last release ? Thanks in advance Marc
View ArticleXMC4800 Ethercat Relax Kit only fpr evaluation ?!
Dear all, outside on the box of the relax kit there is a note that the relax kit is only intended to use for evaluation. Because I like the form factor and the design of this kit I would use it for...
View ArticleEthercat board Beckhoff Slave Stack Code Tool
So sorry that user has got to get this tool from Beckhoff as we are not the owner of this tool.
View ArticleBrand New Version does not work
Even with the new 4.2.4 I ran into the same problem on one machine. A deinstall an reinstall does not help. Could you give me informations on what to delete after a deinstall to really get a fresh...
View ArticleUART Interrupt isn´t working at XMC1100. HELP
Hey, thank you for the example and no i did the signgal connection. A few words, i just rebuild your example and tried it first without reach the Interrupt routine. So i changend my baud rate from...
View ArticleXMC 4500 stops working with interrupts and sd card
Does anyone have any idea of how can I "trick" this fail? Could this be something about more than one instance sharing the same clock?
View ArticleExtern Interrupts
Hello friends, I don't get the ERU to work. The problem is that I want to use a extern pin as interrupt source. I tried to write some example code based on the xmcLib example for the ERU. But I don't...
View ArticleXMC1100 - special UART Command to leave User Productive Mode
Thank you. thats what i need
View ArticleXMC4108 internal oscillator
Hello The accuracy of the internal fast RC-oscillator in factory calibration is +-15% according to the datasheet. Via the internal slow clock source (+-5%) and automatic calibration the reachable...
View ArticleClik here to view.
CCU8 should start other CCU8
Hello, I want that a CCU8 with 1 kHz trigger the start of a 2nd CCU8 with 10kHz w/o CPU intervention. I created 2 CCU8. The one called sample start at init. The other should start at the end of a...
View ArticleBootloader running from Flash
Hello, I have a small problem with my bootloader. I finally made my bootloader to run from flash and receiving the data from pc correctly. I am using an XMC4500 with Dave4. The space reserverd for the...
View Article