ASCLIN on TC234 ADAS problems
Hi Did the code clear CPU ENDINIT bit before accessing register BIV? Some of AURIX critical registers are ENDINIT protected. The following registers are ENDINIT protected: • BTV, BIV, ISP, PMA0, PMA1,...
View ArticleClik here to view.
Xmc1302 p1.4 LED
I have XMC power explorer kit and I am using the the control boards with XMC1302 and XMC4200 for learning. On the XMC1302 board there is a test LED connected to P1.4. I wanted to blink it with the PWM...
View ArticleClik here to view.
Migrating PMSM FOC LIB from DAVE to Keil uVision
Hello everybody, I have been working with XMC4400 by using both DAVE and Keil uVision . When I try to migrate projects from Dave to uVision I can make them work with the help of the document ;...
View ArticleTC389 low level drivers
Hi, Since Aurix Studio does not include tc3xx MCU's, how can I get the drivers?
View ArticleClik here to view.
What happens when reading and flash operation conflict?
Hi Lucas, This depends on whether the flash bank to be accessing the same bank or not. "Read from flash", would mean a read access is done via the SRI bus and "Flash Operation" means the flash bank is...
View ArticleAURIX Compiler
Theoretically you should be able to run the same code by using the Hightec Free Licence only for Evaluation Purposes.
View ArticleTC39 Powerup Start with ED and PD
Can you confirm that you have programmed the UCB_BMHDx_ORIG and UCB_BMHDx_COPY on the PD device? If these are not programmed the debugger will usually set the start address according to your elf file....
View ArticleSMU Configuration Steps
I am also writing here as probably it is also related to safety. I am currently using the TC277_TFT board and in the schematic I see that the external IC TLF35584 is used which Infineon recommends to...
View ArticleHard Fault - XMC 4300 __asm("BKPT 0\n")
Hello, I´m working with an XMC4300. Sometimes I have the problem that the uC end in a Hard Fault. I have no clue what to do. I enabled Hard Fault debugging support in the CPU_CTRL_XMC4_0 My application...
View ArticleClik here to view.
Emulator Debug Port Secure error on Trace
Hello, I have written the invalid values to the BMHD0 where there is no values in the other BMHDs. This invalid value locks the ECU. Attachment 4512 According to the schematic, it is not possible for...
View ArticleClik here to view.
Default Handler disrupting FreeRTOS program
In the CPU_CTRL_XMC4 APP UI settings: Attachment 4514 Regards, Jesus ????? cpu_ctrl_xmc4_exception_settings.png‎ (12.4 KB)
View Articlecompile source code with command line for Aurix Tricore TC277
Hello, I work on the Aurix tricore TC277 microcontroller with the Hightec compiler which is with eclipse, but now I need to compile my source code with command line, that means without using eclipse....
View ArticleClik here to view.
OPCUASERVER_LWIP_XMC47 on xmc4800 automation board
Hi, I just tested the example in the XMC4700 RelaxKit and there it is working without problems. Attachment 4515 In the Libraries/lwip/port/nosys/netif/ethernetif.c you need to adapt the pins as...
View ArticleClik here to view.
XMC1202 with ULINK2?
Hi, The BMI is correct. Can you try by upgrading the JLink software? If I try the same I get the following (using latest JLink software) Code: Load...
View ArticleCan't enable LMU/SRAM read buffers in TC29x
Hi jjorba. For TAG IDs: the idea with Safe/Non-Safe TAG IDs is that you can use the ACCENx registers to restrict which bus masters have access to various parts of the system. No impact to LMU...
View ArticleClik here to view.
TLE9879QXA40 Arduino Shield Not Responive
Hello, I have loaded the sketch "bldc_shield_blinky_test" and it looks like the shield cannot be found. I have tried two different Arduino Unos as well with the same result. When I open the serial...
View ArticleClik here to view.
ASCLIN on TC234 ADAS problems
Quote: Originally Posted by VincentWan Hi Did the code clear CPU ENDINIT bit before accessing register BIV? Some of AURIX critical registers are ENDINIT protected. The following registers are ENDINIT...
View ArticleIGBTs with short circuit capability
Hi, could you please tell me why to use IGBTs with short circuit capability? What exactly do you mean with short circuit?
View ArticleRg for drives
Dears, can anybody tell me how to figure out the right Rg for drive applications? Ty Max
View Article