TC299TX Memtool Failed to read target status
Hello, if have a problem connecting the memtool to my Aurix TC299TX. Connect fail always with the message: Code: Message from component 'IMTMemtool' : Can't connect to Target Message from component...
View ArticleOnly one POSIF unit mapped to XMC1400 with VQFN48 package
Hello Guys, while creating schematic with the XMC1400 I experienced a problem with the VQFN48 package. In the datasheet on page 11 it tells me that the XMC1402-Q048 has got two POSIF units. BUT by...
View ArticleClik here to view.
ECAT Slave to Slave communication
Hi Lukas, for detailed Information on how to setup the network with the EtherCAT master you are using, please get in contact with your provider. For TwinCAT3 you can find a description inside the pdf...
View ArticleXMC4500 CAN, listen only but activate and tx on special ID
Hi, Does someone know if there is any way to use a XMC4500 as a listen only can node. And if I receive a special message I will activate my tx and answer with may definde message. I should ignore all...
View ArticleProblems with erasing and programming PFlash on AURIX TriCore (tc0), TC277-DC
I've whittled the code down from Infineon to just this little bit: static void FlashDemo(void) { uint16 endinitSfty_pw; uint32 sector_addr = 0xaf008000; endinitSfty_pw =...
View ArticleDirect FOC motor control
Hi! I'm using XMC1302 controller for controlling BLDC motor using FOC. The motor works fine with V/f Startup to FOC Speed control technique. However, I want to control with 'Direct FOC' technique. Can...
View ArticleAUIRS20302S and IRFS3607 for BLDC Motor application.
hi, i am supporting a customer doing E-bike / E-scooter and hence we are promoting power devices eg. power mosfet and gate driver IC. This customer is interested in 36V system and using BLDC motor for...
View ArticleHow to create One Shot Timer ?
Hi Richard, I suggest to take a look at the CCU4_SLICE_CONFIG APP (Similar option is available in PWM APP also). There you have an "Single-shot mode" option which should suit your needs perfectly. All...
View ArticleXmc4800 - ieee1588
Hi Jesus and Loic, We are thinking of implementing IEEE1588 on XMC4500/4700 platform, but are not sure if there is a way to share PTP system time with other XMC hardware without adding time uncertainty...
View ArticleEmulating I2S with SPI
Hi, New to this forum and also to the Aurix family. I am considering a TC233 device for a project where we need to emulate I2S (mono, so no frame clock) using the SPI controller in this device. I am...
View ArticleFAQ for XMC4800 EtherCAT
Hi all, I'm working on XMC4800 EtherCAT with SSC tool. I've enabled EoE for my application, and I've given a IP address for the XMC. Now, how do I check the communication ? I mean, how do I check the...
View ArticleXMC4800 EoE
Hi all, I'm working on XMC4800 EtherCAT with SSC tool. I've enabled EoE for my application, and I've given a IP address for the XMC. Now, how do I check the communication ? I mean, how do I check the...
View ArticleClik here to view.
Flash read protection - cannot connect anymore
Quote: Originally Posted by SashaBelykh To connect to your device you can use ASC BOOT Loader. The shortest way is to use any kind of COM Port (usually USB-UART device) to lines P1.4 P1.5 and connect...
View ArticleWhat is the acronym description for DAM in TC297
The Default Application Memory is an SRI peripheral providing access to volatile memory resources.
View ArticleEth_lwip 4.0.16
Hi all, Solution found: Jesus has informed that in 4.0.16, Infineon had overlooked the ticking of 'Accept broadcast frames' by default, on the Network Interface tab. And in 4.0.10, the behaviour of...
View ArticleDetect that device has been disconnected from PC USB Host
Scenario: The XMC45 is connected to a PC using a USB cable. The cable is then removed. I want to detect this event, but how?. I've seen several similar questions on the forum, but no satisfactory...
View ArticleDatasheet EUPEC FM35R12KE3ENG
great Information Thanks a lot M Sc Nursing Course in BangaloreNursing Colleges in Gujarat Nursing Colleges in Himachal PradeshNursing Colleges in Kerala
View ArticleOnly one POSIF unit mapped to XMC1400 with VQFN48 package
Thanks for the quick answer, that's really helpful!
View ArticleWorkspace folder
Hi, While DAVE was not open, I renamed my workspace folder, due request from management. When I reopen my project, everything builds and works fine. But, I find that building causes my old workspace...
View Article