Why am i getting 0xFF from the QSPI Rx register ?
Hi Lucas, This is the correct behaviour of the SPI RXEXIT register. The RXFIFO has a property that a read access from an empty RXFIFO generates an underflow interrupt, and delivers only “1” bits, which...
View ArticleWhat is the min. duration time for detection of primary voltage monitoring...
Hi Tita, The primary UV monitor operation based on tracking ADC to measure supply voltages. It's clocked and the value is updated every PMS clock cycle. However, due to tracking ADC nature, the max...
View ArticleWhich operating systems are supported by MemTool?
Hi Christine, Supported operating systems are shown in the release notes of the MemTool. e.g. In the MemTool version: 4.8.1 (11.10.2019), the following operating systems are supported. Microsoft...
View ArticleWhich IPM is best suited for my application?
Where can I find a full system solution for my application? Do you provide any tools that could help me? Have a great weekend!
View Articlehow to simulate a clock monitoring failure
Can someone guide me how to simulate a clock monitoring failure? Now I`ve test it by following 2 steps: 1. set GTMSEL(GTM monitoring frequency) to 7.5MHz: SCU_CCUCON4.B.GTMSEL = 3u 2. set GTMDIV=20...
View ArticleProper way to modify SCU_CCUCON0.BAUD2DIV
That's great, I did however forget to say you also need to check the status of the CCUCONx.LCK bit. You can only update the SFR if this is equal to 0.
View ArticleTricore using backup clock even though external clock provided
Was looking at SCU_CCUCON0, and I noticed CLKSEL = 0. This seems odd, because I do have an external xtal on the board. Does the CLKSEL need to be set in the init code, or is this indicative of a clock...
View ArticleWhat is an IPM?
Happy New Year to you too Fränce! An IPM, which is short for Intelligent Power Module, is a highly integrated, compact module that includes a power inverter (IGBT or MOSFET), gate driver IC, and...
View ArticleEvaluate IPM
Yes there are! They are called iMOTION MADKs, short for Modular Application Design Kits. These are reference design boards that not only include all the circuitry required to run a motor, but are also...
View ArticlePerformance measurement IPM
If you are not trying to measure the performance, but you know your motor drive conditions and the thermal environment of the IPM, then you can use the IPM Simulation Tool. This tool estimates the...
View ArticleNeed QSPI TX shift register status on TC234
I'm trying to determine the QSPI TX shift register status so I can ensure all bits are sent before deasserting the C. The context: o I need to send data via SPI at fairly high speed (~25 Mhz). o The L2...
View ArticleDAVE4 plugins
Installing TM Terminal Add http://download.eclipse.org/tm/terminal/marketplace to your Available Software Sites.
View ArticleMissing Git in Dave V4.4.2
Did you check https://www.infineonforums.com/threa...ll=1#post24079
View ArticleClik here to view.
IR2113 For VFD use, one driver keeps failing
Good day, I am trying to use three IR2113 drivers for a VFD. I have followed the application guide as attached. I am using six STF13N95K3 n-channel MOSFETs whose datasheet is also attached. Upon...
View ArticleUsing MemTool to flash TC297 and TC397
Hi, we want to use the MemTool to Flash an Intel Hex file to the TC297 reference board. we have come across various posts and information about risks in flashing UCBs or possible requirement of boot...
View ArticleLooking for the XC164CM UCAN Starter kit USB stick
Crazy that nobody else has found this yet. Photo Booth Rental Kalamazoo
View ArticleIGBT test circuit
I have modelled an IGBT diode pack from Infineon in SABER RD . I want a test circuit to obtain Eon Eoff curve. Can you help me out.
View ArticleBug / Undefine behaviour in the PWM_CCU8 / PWM_CCU8_Stop function
In case this helps someone else, I believe there is a bug / undefined behaviour in the PWM_CCU8 App.... https://www.infineonforums.com/threa...-with-PWM_CCU8 I am using the PWM_CCU8 App to drive two...
View Article