Integrated Development Environment (IDE) (AURIX Development Studio...
Hello kamorn, You should receive 2 emails after the registration process, if not, please try again registering another time. We are trying to improve the download process, could you please report your...
View ArticleGetting Started with iMOTION material. Beginner? Start here!!!
Please view the video linked below or presentation format. This goes over all you need to know about how to get started with iMOTION using an MADK set-up and the latest MCE Tools. in additional, the...
View ArticleIntegrated Development Environment (IDE) (AURIX Development Studio...
Hello kamorn, You should receive 2 emails after the registration process, if not, please try again registering another time. We are trying to improve the download process, could you please report your...
View ArticleClik here to view.
XMC4400 connection matrix for ccu4 input selector
Hello, I'm looking for said table, eg CCU40.IN0A to PORTS,... basically this https://www.infineonforums.com/threa...elector-Matrix but for the xmc4400. I can't find it in the xmc4400 data sheet nor in...
View ArticlePLL N-Multiplier , K2-Divider Value
Hi Now we using fSYS Clock at 40Mhz via N-Multiplier setting as '16' , and K2-Divider setting as'2'.(Int OSC 5Mhz) so,Is it possible change the N, K2 value as '24' and '3' ? I think there is same fSYS...
View ArticleProgram execution
Hi Again After i changed the location of Program through linker script, the program was able to run. I located the program through LDF Editor. I saw also differents in .hex of Program in two cases. And...
View ArticleAurix code generator
Hi, during development I sometimes have to change Aurix Tc22x registers, The problem happens when those registers influence other modules( f.e clock registers). Its coming out after and it takes long...
View ArticleA general question about peripherie ????
I have two programs one for bootloader and one for application program. And i also disable all the interrupts before i jump from bootloader to application program. When i initialise a peripherie part...
View ArticleUnable to build imported projects from gits in Aurix development studio
Hello Gajanan, you are using the Aurix Development Studio v1.1.6, which is very old. Currently, the ADS has reached the version v1.1.10, please update to the latest version (AURIX™ Development Studio)...
View ArticleClik here to view.
Motor configuration
hello Casey, I have replied you in PM. While doing our research we reached this results: Here you can see the current and motor speed. The motor is rated at 7200 rpm max, and there was some load. It...
View ArticleLong-term Investments for future years
Money ranges are comparatively safe. There is a mutual fund where a group of investors invest their money with each other to buy stocks and options, bonds, or additional investments. He did work on...
View ArticleTC399: read while write
RWW is supported between Program and Data Flash. Concerning Program Flash this is supported only between the different PFLASH banks. The TC39x has 16Mbytes of internal PFlash and supports 6 banks, 5...
View ArticleClik here to view.
Start bldc motor in different voltage imm101t
Quote: Originally Posted by huyrua291996 Thanks Casey, I got it. I use intial angle sensing to start-up.After serveral times tuning, I realize my flux estimator time constant was not good enough and...
View ArticleBootstrap capacitor selector - Excel Tool
Dear colleague, Can you share the excel calculation for bootstrap capacitor selector? Thanks
View ArticleGaN HEMT - IGOT60R070D1 NC pad connection
The NC pads are not bonded internally to the die. You may connect the NC pins to the drain pins.
View ArticleTC29x
Hello, Kindly, How can I calculate Erase Speed, Write Speed for TC1791 for both Data Flash, Program Flash? as I found erase Time, Write Time per Page or per sector but I can't find the size of page or...
View ArticleCAN demo pins
Hello, Thanks for your help. It has been certainly useful. I have tried the example MULTICAN_1_KIT_TC297_TFT and it works. I can see the the loopback mode is enabled. In file MULTICAN.c...
View ArticleERU triggers the VADC on Aurix TC27x
Hi to all, i want to control the Vadc over an external Interrupt. For this puposes i need the ERU module. I use also the iLLD's. I have read the ERU Training with interrupt generation and this worked...
View ArticleQSPI reading problem
Thanks for response. I changed my PLL setting to receive fPLL equal to ~120Mhz My startup registers are: SBCU_CON : 0xff09ffff DCON0: 0x0 PCON0: 0x0 GTM_CLC: 0x0 FLASH0_FCON: 0x910000 SCU_CCUCON0:...
View Article