Migration from XMC4500 to XMC4700
Hi Jesus Here an short update from our side 1. On our Testproject we do net see any DMA Errors when the Trap Occurs 2. We have produced 50 new PCB with the XMC4500 and they all work fine. We have 20...
View ArticleProblem while working with xSPY
Hi My english is not so good, but I think that you will understand. I have problem with xSPY when I want to see voltage signal. I use PMSMFOCSL01 control on XMC1300. xSPY don't show the whole period so...
View ArticleClik here to view.
XMC 2Go with XMC_2Go_Inital_Start_v1.3 project: Only garbage from the serial...
Hi, today I tried to revive the XMC 2Go that I had bought some time ago with DAVE 4 64-bit under Windows 10 64-bit. After compiling and uploading the XMC_2Go_Inital_Start_v1.3 project I can see the...
View ArticleIRMCK099M custom GPIO functions
Hello Matteo: We bought the Eval_M1_99M and Eval_M1_36_84A. We also downloaded and installed all the necessary SW. When I start the XMC_flasher , it said "Please first connect an emulator". I followed...
View ArticleHRPWM problem on XMC 4200
Hello, XMC4400 and XMC4200 have typically 2 different main clock frequencies: 120MHz and 80MHz respectively. As the Minimum step width of HRPWM is fixed to 150ps, the maximum number of steps of HR (CR1...
View ArticleCCU4: Measure PWM duty cycle and period
Hey Fesinator, Mine originally overflowed as well. I changed the "Prescaler initial value" under the General Settings of CCU_Slice_Config so that my CCU4 clock was slower without affecting the CPU...
View ArticleThe Example code of AP32337 - XMC1000 - Software update
Is anybody know how can download the example code of AP32337 - XMC1000 - Software update of XMC1000 microcontrollers using an ASC interface. Usually I can download the example code from the infineon...
View ArticleDAVE TIP of the day: What to do when get solver errors?
Hello Laura, In the Workspace folder, there is a .metadata folder. Try to remove it and restart Dave, it fixed my issues with Solver Jorge
View ArticleClik here to view.
I2C_EXAMPLE_XMC4500 not working on AUT_ISO board
Hi Jorge, It´s really strange, while I ran the same example that you used and also an example that I will send you and both of them are working for me. Can you verify that you really transmitted 0xFF?....
View ArticleBluetooth Communication
this is great, BUT pin security is a joke in Bluetooth world. Is there anything dangerous exposed over this link? can you break engine by just programming megasquirt wrong way?
View ArticleWhat is the difference between FADC and ADC in XMC4000?
Hi, I saw "A/D Input Lines" and "A/D Input Lines (incl. FADC)" at XMC4000 device selection web page; https://www.infineon.com/xmc4000 What is the difference between these two ADCs? I believe XMC has...
View ArticleSPI Master and Slave using DMA
Hi Niklas, ...not sure if you have already got it in the meantime. Otherwise please take a look here: https://www.infineonforums.com/threa...aster-to-Slave
View ArticleEBU settings with Dave4
We want to use Dave4 to configure and program the Controller XMC4700. In our design we have a FPGA which will be connected with the demultiplexed or multiplexed external bus. So we have to configure...
View ArticleSept 7, 2016 New Release of DAVE, DAVE APPs and other Libraries
Today we published new versions of DAVE, DAVE SDK, DAVE APPs, XMC Lib, Device Descriptions, and Device Support Pack. DAVE v4.3.2 and DAVE SDK v4.3.2 In addition to fixes of various issues we added a...
View ArticleSept 7, 2016 New Release of DAVE, DAVE APPs and other Libraries
Today we published new versions of DAVE, DAVE SDK, DAVE APPs, XMC Lib, Device Descriptions, and Device Support Pack. DAVE v4.3.2 and DAVE SDK v4.3.2 In addition to fixes of various issues we added a...
View ArticleDead time on our PWM 3-phase motor control
We are trying to enable dead time on our PWM 3-phase motor control. We are using XMC4400 motor kit. We are using Dave CE 4.2.8. We have tried two different options to enable the dead time but both fail...
View ArticleClik here to view.
xmc 4500 I2C no output and all USIC register appeear as 0xFFFFFF
Hi all! I've having an issue with my XMC4500 relex kit and usic channel. Here's my code: Code: volatile uint8_t tx_completion_0 = 0; /* Transmit callback handling */ void tx_callback_0(void) {...
View ArticleProblem with storage of large const array
Thank you for your effort and the proof that it works as intended. Meanwhile I found the problem. It was a stupid mistake of my own :mad:. In my test I put a "volatile" in front of it in order not to...
View ArticleImproving Code flash speed using mini wiggler
Hi I am using miniwiggler to flash code onto TC1782 but its awfully slow. Can some one throw ideas in improving the speed? Thanks Ram
View Article